Priimame kriptovaliutą — taip monetos, kurias turite, gali nupirkti tikrą techniką.Mokėkite kriptovaliuta, išleiskite ją tikrai technikai. Nemokamas apdraustas pristatymas visame pasaulyje virš 399 $. Paprastos, be žymų siuntos dėžės, siunčiamos iš Vokietijos.Nemokamas apdraustas pristatymas virš 399 $. Jūsų kursas fiksuojamas 30 minučių, kai tik prasideda atsiskaitymas.Kursas fiksuojamas 30 minučių. Kiekvienas gaminys užplombuotas, jo serijos numeris patikrintas, ir jam taikoma 24 mėnesių garantija.Užplombuota, 24 mėnesių garantija.

Stebimos prekės Prisijungti
Black standalone SATA duplicator with 16 x 2 LCD and three drive slots

EZ Dupe, Inc.

EZ Dupe, Inc. H03HSATB 1-to-3 SATA duplicator

SKU CH-B3WM-QV2AN

Standalone SATA duplicator copies one drive to three at 150 MB/s with four copy modes and four DoD-compliant erase modes

  • TypeHard Drive Duplicator
  • Panel ColorBlack
  • Operating TypeStandalone
  • Display16 x 2 LCD
  • ConnectorSATA
  • Target1 to 3

Target 1 to 3

Data Transfer Rate 150MB/s

Perbrauktos versijos egzistuoja, bet šiame sandėlyje jų nėra.

  • Copies up to 3 SATA drives simultaneously at 150MB/s
  • Four duplication modes including quick copy and full media copy
  • Four erase modes including DoD 3-pass and 7-pass standards
  • Standalone operation with 16×2 LCD and no host computer required
  • Supports both 2.5" and 3.5" SATA drives without adapters

Standalone SATA Duplicator

The EZ Dupe H03HSATB is a standalone hard-drive duplicator and sanitiser that copies one SATA source drive to up to three target drives without a host computer. It accepts both 3.5-inch and 2.5-inch SATA hard disks and solid-state drives directly in its slot-load bays. A 16 x 2 LCD panel and indicator lights show job progress and status. The unit runs on 115-230 V AC power at 50 or 60 Hz and includes 128 MB of buffer memory driven by an Athena controller.

IT teams and forensic labs needing secure.

This duplicator suits IT departments, data-recovery specialists and forensic examiners who must clone or erase SATA drives in a controlled, air-gapped environment. Four copy modes — Quick Copy, Whole Media, All Partitioned and Percentage Copy — handle defined and undefined file systems. Four erase modes, including DoD 3-pass and 7-pass to the 5220.22-M standard, meet strict sanitisation policies. Buyers who need to duplicate more than three targets simultaneously or who require interfaces other than SATA should consider other equipment.

150 MB/s maximum copy speed per slot

The specification that determines suitability is the 150 MB/s data transfer rate, equivalent to 9 GB per minute, sustained independently on each of the three target ports. This throughput lets a full 1 TB SATA drive clone in roughly two hours per slot. If your workflow demands higher per-port bandwidth or support for non-SATA media, this model will not meet that requirement.

Privalumai

  • Copies up to 3 SATA drives simultaneously at 150MB/s
  • Four duplication modes including quick copy and full media copy
  • Four erase modes including DoD 3-pass and 7-pass standards
  • Standalone operation with 16×2 LCD and no host computer required
  • Supports both 2.5" and 3.5" SATA drives without adapters

Specifikacijos

BrandEZ Dupe
TypeHard Drive Duplicator
ModelH03HSATB
Part NumberH03HSATB
Panel ColorBlack
Operating TypeStandalone
Display16 x 2 LCD
ConnectorSATA
Target1 to 3
Buffer Memory128M
ControllerAthena Controller
Supported MediaSATA Hard Drive Disk / SATA Solid State Drives
Data Transfer Rate150MB/s
Load TypeSlot
Key FeaturesDuplication
FeaturesIndication Lights
Power SupplyAC: 115-230 V, 50/60 Hz

Kiti šio modelio variantai

Dar 5 toje pačioje serijoje

Ta pati šeima, bet skiriasi atmintis, aušintuvas ar dažnis — palyginkite prieš apsispręsdami.

Klausimai apie šią prekę

How do I install drives into the H03HSATB duplicator and which step is often missed?

Insert up to three SATA 3.5" or 2.5" drives directly into the slot-load bays; the step often missed is setting the correct copy mode — Quick Copy, Whole Media, All Partitioned or Percentage Copy — before pressing start.

What maintenance or replacement will the H03HSATB need over time?

The unit has no user-serviceable parts; keep the slot openings clear of dust and verify the 128M buffer and Athena Controller operate normally — if a drive bay fails, the whole duplicator requires service.

What limit appears first during sustained high-speed duplication on the H03HSATB?

The 150MB/s per-slot transfer rate is the ceiling; sustained runs at that speed are bounded by the 128M buffer and the Athena Controller throughput, so thermal throttling or buffer saturation will show up before the 115-230 V AC supply becomes a factor.

Taip pat šiame skyriuje

Kiti pirkėjai taip pat lygino

Ta pati lentyna, tas pats atsiskaitymas — aštuonios monetos ir 30 minučių fiksuotas kursas.