Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Black standalone SATA duplicator with 16 x 2 LCD and three drive slots

EZ Dupe, Inc.

EZ Dupe, Inc. H03HSATB 1-to-3 SATA duplicator

SKU CH-B3WM-QV2AN

Standalone SATA duplicator copies one drive to three at 150 MB/s with four copy modes and four DoD-compliant erase modes

  • TypeHard Drive Duplicator
  • Panel ColorBlack
  • Operating TypeStandalone
  • Display16 x 2 LCD
  • ConnectorSATA
  • Target1 to 3

Target 1 to 3

Data Transfer Rate 150MB/s

Přeškrtnuté varianty existují, ale zde nejsou skladem.

  • Copies up to 3 SATA drives simultaneously at 150MB/s
  • Four duplication modes including quick copy and full media copy
  • Four erase modes including DoD 3-pass and 7-pass standards
  • Standalone operation with 16×2 LCD and no host computer required
  • Supports both 2.5" and 3.5" SATA drives without adapters

Standalone SATA Duplicator

The EZ Dupe H03HSATB is a standalone hard-drive duplicator and sanitiser that copies one SATA source drive to up to three target drives without a host computer. It accepts both 3.5-inch and 2.5-inch SATA hard disks and solid-state drives directly in its slot-load bays. A 16 x 2 LCD panel and indicator lights show job progress and status. The unit runs on 115-230 V AC power at 50 or 60 Hz and includes 128 MB of buffer memory driven by an Athena controller.

IT teams and forensic labs needing secure.

This duplicator suits IT departments, data-recovery specialists and forensic examiners who must clone or erase SATA drives in a controlled, air-gapped environment. Four copy modes — Quick Copy, Whole Media, All Partitioned and Percentage Copy — handle defined and undefined file systems. Four erase modes, including DoD 3-pass and 7-pass to the 5220.22-M standard, meet strict sanitisation policies. Buyers who need to duplicate more than three targets simultaneously or who require interfaces other than SATA should consider other equipment.

150 MB/s maximum copy speed per slot

The specification that determines suitability is the 150 MB/s data transfer rate, equivalent to 9 GB per minute, sustained independently on each of the three target ports. This throughput lets a full 1 TB SATA drive clone in roughly two hours per slot. If your workflow demands higher per-port bandwidth or support for non-SATA media, this model will not meet that requirement.

Přednosti

  • Copies up to 3 SATA drives simultaneously at 150MB/s
  • Four duplication modes including quick copy and full media copy
  • Four erase modes including DoD 3-pass and 7-pass standards
  • Standalone operation with 16×2 LCD and no host computer required
  • Supports both 2.5" and 3.5" SATA drives without adapters

Specifikace

BrandEZ Dupe
TypeHard Drive Duplicator
ModelH03HSATB
Part NumberH03HSATB
Panel ColorBlack
Operating TypeStandalone
Display16 x 2 LCD
ConnectorSATA
Target1 to 3
Buffer Memory128M
ControllerAthena Controller
Supported MediaSATA Hard Drive Disk / SATA Solid State Drives
Data Transfer Rate150MB/s
Load TypeSlot
Key FeaturesDuplication
FeaturesIndication Lights
Power SupplyAC: 115-230 V, 50/60 Hz

Další verze tohoto modelu

Dalších 5 v této řadě

Stejná řada, jiná paměť, chladič nebo takt — porovnejte, než se rozhodnete.

Otázky k tomuto produktu

How do I install drives into the H03HSATB duplicator and which step is often missed?

Insert up to three SATA 3.5" or 2.5" drives directly into the slot-load bays; the step often missed is setting the correct copy mode — Quick Copy, Whole Media, All Partitioned or Percentage Copy — before pressing start.

What maintenance or replacement will the H03HSATB need over time?

The unit has no user-serviceable parts; keep the slot openings clear of dust and verify the 128M buffer and Athena Controller operate normally — if a drive bay fails, the whole duplicator requires service.

What limit appears first during sustained high-speed duplication on the H03HSATB?

The 150MB/s per-slot transfer rate is the ceiling; sustained runs at that speed are bounded by the 128M buffer and the Athena Controller throughput, so thermal throttling or buffer saturation will show up before the 115-230 V AC supply becomes a factor.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.