Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Black standalone SATA duplicator with 16x2 LCD, three drive slots, indicator lights

EZ Dupe, Inc.

EZ Dupe, Inc. HD Leopardo H03PROHEB 1-to-3 SATA duplicator

SKU CH-CM04-B2JV1

Standalone duplicator copies up to three SATA drives at 300 MB/s with four copy modes and seven erase modes

  • TypeHard Drive Duplicator
  • Panel ColorBlack
  • Operating TypeStandalone
  • Display16 x 2 LCD
  • ConnectorSATA
  • Target1 to 3

Target 1 to 3

Data Transfer Rate 300MB/s

Yliviivatut versiot ovat olemassa, mutta niitä ei ole varastossa täällä.

  • Copy three SATA drives simultaneously at 300 MB/s per slot
  • Four duplication modes including quick and full copy options
  • Seven erase modes meeting DoD 5220.22-M security standards
  • Standalone operation with 16×2 LCD — no host computer required
  • Supports 2.5" and 3.5" SATA drives without adapters

Duplicator for three SATA drives

The HD Leopardo H03PROHEB is a standalone duplicator that copies one SATA source drive to up to three target drives simultaneously. It accepts both 3.5 and 2.5 inch SATA hard drives and solid state drives without adapters. The unit operates without a host computer, software or network connection. A 16 x 2 LCD panel and indicator lights show job progress and status.

Upgrade from single-bay copiers

Moving from a one-to-one duplicator to this 1-to-3 model triples per-session throughput when you regularly clone the same image to multiple drives. The jump is worth it when production batches exceed a single target or when you need the seven erase modes — including DoD 3-pass and 7-pass to 5220.22-M standards — for compliant sanitisation. Copy speed reaches 300MB per second, or 18GB per minute, across each slot.

Check power and drive fit

Verify that your mains supply delivers 115 to 230 V at 50 or 60 Hz, matching the built-in AC input. Confirm that every source and target drive uses a SATA interface and fits the 3.5 or 2.5 inch form factor; other interfaces or sizes are not supported. The slot-load design requires no caddies, but drives must be inserted directly into the three target bays and one source bay.

Kohokohdat

  • Copy three SATA drives simultaneously at 300 MB/s per slot
  • Four duplication modes including quick and full copy options
  • Seven erase modes meeting DoD 5220.22-M security standards
  • Standalone operation with 16×2 LCD — no host computer required
  • Supports 2.5" and 3.5" SATA drives without adapters

Tekniset tiedot

BrandEZ Dupe
TypeHard Drive Duplicator
ModelHD Leopardo
Part NumberH03PROHEB
Panel ColorBlack
Operating TypeStandalone
Display16 x 2 LCD
ConnectorSATA
Target1 to 3
Buffer Memory128M
ControllerAthena Controller
Supported MediaSATA Hard Drive Disk / SATA Solid State Drives
Data Transfer Rate300MB/s
Load TypeSlot
Key FeaturesDuplication
FeaturesIndication Lights
Power SupplyAC: 115-230 V, 50/60 Hz

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

Does the duplicator accept both 2.5" and 3.5" SATA drives without an adapter?

Yes, the HD Leopardo H03PROHEB supports 2.5" and 3.5" SATA hard drives and solid-state drives directly in each of the three target slots, no adapter required.

How do I start a copy job on the standalone unit, and what is the common mistake?

Insert the source drive into the source slot and up to three target drives into the target slots, select one of the four copy modes via the 16x2 LCD menu, then press Start; the frequent error is choosing Quick Copy when the file system is unrecognised, which copies nothing — use Whole Media or Percentage Copy instead.

Which erase mode should I choose for a drive that will be reused internally, and does the unit need servicing?

For internal reuse, Quick Erase removes file references in seconds; the duplicator has no user-serviceable parts and requires no periodic maintenance beyond keeping the slots clear of dust.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.