EZ Dupe, Inc. HD Leopardo H09PROHEB 1-to-9 SATA duplicator
- Hard Drive Duplicat…
- Black
Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.
EZ Dupe, Inc.
Standalone duplicator copies up to 23 SATA drives at 300MB/s with four copy and seven erase modes
Data Transfer Rate 300MB/s
Yliviivatut versiot ovat olemassa, mutta niitä ei ole varastossa täällä.
The EZ Dupe HD Leopardo H23PROHEB copies one SATA source to 23 targets at up to 300 MB/s. It handles both 3.5 and 2.5 inch drives without adapters and runs standalone with a 20 x 2 LCD and Athena controller. The 128 MB buffer keeps throughput steady across all slots. Operates on 115 to 230 V AC at 50 or 60 Hz.
Moving up from a one-to-one copier or a unit limited to lower transfer rates adds 23 simultaneous targets and 18 GB/min per slot. The jump is worth it when you must image dozens of drives daily or need four copy modes and seven erase modes including DoD 5220.22-M three-pass and seven-pass. Single-drive workflows or occasional backups will not use the capacity.
Verify every target drive uses a SATA interface and fits 3.5 or 2.5 inch form factor. Confirm the rack or bench can supply 115 to 230 V AC at 50 or 60 Hz for the built-in power supply. No host computer or software is required, so ensure physical access to the front-loading slots for unattended operation.
| Brand | EZ Dupe |
|---|---|
| Type | Hard Drive Duplicator |
| Model | HD Leopardo |
| Part Number | H23PROHEB |
| Panel Color | Black |
| Operating Type | Standalone |
| Display | 20 x 2 LCD |
| Connector | SATA |
| Target | 1 to 23 |
| Buffer Memory | 128M |
| Controller | Athena Controller |
| Supported Media | SATA Hard Drive Disk / SATA Solid State Drives |
| Data Transfer Rate | 300MB/s |
| Load Type | Slot |
| Key Features | Duplication |
| Features | Indication Lights |
| Power Supply | AC: 115-230 V, 50/60 Hz |
Tämän mallin muut versiot
Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.
The unit provides 23 target slots, each accepting a 3.5" or 2.5" SATA drive without an adapter.
Insert the source drive in the source slot and target drives in the target slots, power on the unit, select the desired copy mode on the 20 x 2 LCD, then press Start; the common mistake is pressing Start before confirming the mode.
The slot-load SATA connectors and the internal power distribution board are the parts most likely to wear out after repeated drive insertions.
Myös tällä osastolla
Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.
Valuutta, jolla maksetaan, sekä valuutta, jossa hinnat näytetään.
Lähetetään lompakostasi kassalla
Vain näyttöä varten — hinnat ovat Yhdysvaltain dollareissa
Valuuttaa ei löytynyt.
Valitse kieli, jolla sivusto puhuu sinulle.
Ei vastaavaa kieltä.
Uusi täällä?
Onko sinulla jo tili?
Automaattista palautusta ei ole: kauppa ei lähetä sähköpostia lainkaan, joten kertakäyttöistä linkkiä ei ole mistä pyytää. Jätä osoite tilille, niin se käsitellään käsin.
Pyyntö kirjattu
Mikään ei ole tulossa sähköpostiisi — tämä kauppa ei lähetä sähköpostia lainkaan. Joku käsittelee nämä pyynnöt käsin.
Muistitko sen?