Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään

EZ Dupe, Inc.

EZ Dupe, Inc. H15HSATB duplicator 15-target 150MB/s SATA 128M buffer

SKU CH-0FNK-Y327S

Standalone duplicator copies up to 15 SATA 3.5" or 2.5" drives at 150 MB/s with 128 MB buffer and DoD erase modes

  • TypeHard Drive Duplicator
  • Panel ColorBlack
  • Operating TypeStandalone
  • Display16 x 2 LCD
  • ConnectorSATA
  • Target1 to 15

Target 1 to 15

Data Transfer Rate 150MB/s

Yliviivatut versiot ovat olemassa, mutta niitä ei ole varastossa täällä.

  • Copies up to 15 SATA drives simultaneously at 150MB/s per slot
  • Four copy modes include quick, full, partition and percentage options
  • Four erase modes cover quick, full, DoD 3-pass and DoD 7-pass standards
  • Standalone operation with 16×2 LCD needs no host PC for security
  • Supports 2.5" and 3.5" SATA HDDs and SSDs without adapters

What this duplicator does

The EZ Dupe H15HSATB is a standalone hard-drive duplicator that copies up to 15 SATA drives at once. It handles both 3.5-inch and 2.5-inch SATA hard-disk drives and solid-state drives without adapters. A 128 MB buffer and Athena controller deliver a sustained 150 MB/s per slot. Operation is driven by a 16 x 2 LCD and status lights.

Who should use it and who should not

IT teams and data-centre staff needing fast, secure mass duplication or sanitisation of SATA drives will benefit from the four copy modes and four DoD-compliant erase modes. Buyers who need to duplicate drives with interfaces other than SATA, or who require network-attached or software-driven operation, should look at a different solution.

The specification that decides fit

The duplicator provides 15 target slots with a native SATA connector for each slot and a slot-load mechanism. If the workflow demands more than 15 simultaneous targets or a different drive interface, this unit will not meet the requirement.

Kohokohdat

  • Copies up to 15 SATA drives simultaneously at 150MB/s per slot
  • Four copy modes include quick, full, partition and percentage options
  • Four erase modes cover quick, full, DoD 3-pass and DoD 7-pass standards
  • Standalone operation with 16×2 LCD needs no host PC for security
  • Supports 2.5" and 3.5" SATA HDDs and SSDs without adapters

Tekniset tiedot

BrandEZ Dupe
TypeHard Drive Duplicator
ModelH15HSATB
Part NumberH15HSATB
Panel ColorBlack
Operating TypeStandalone
Display16 x 2 LCD
ConnectorSATA
Target1 to 15
Buffer Memory128M
ControllerAthena Controller
Supported MediaSATA Hard Drive Disk / SATA Solid State Drive
Data Transfer Rate150MB/s
Load TypeSlot
Key FeaturesDuplication
FeaturesIndication Lights
Power SupplyAC: 115-230 V, 50/60 Hz

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

Should I choose the 15-target model or a smaller duplicator for my workload?

This unit has 15 target slots, so you can duplicate up to fifteen SATA drives at once; pick it if you regularly need that many concurrent copies.

What does the 150 MB/s headline speed mean once the duplicator is running?

The 150 MB/s rate is the maximum per-slot throughput; actual time depends on the source drive's sustained read performance.

The unit uses SATA — what does that cap in practice?

The SATA connectors limit you to 3.5" or 2.5" SATA hard drives and solid-state drives; other interfaces are not supported.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.