Vi tar imot kryptovaluta — slik kan kryptovalutaene du eier, kjøpe ekte maskinvare.Betal med krypto, bruk den på ekte maskinvare. Gratis, forsikret levering verden over for bestillinger over 399 $. Nøytrale kartonger uten merking, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Kursen din er låst i 30 minutter når kassen åpnes.Kurs låst i 30 minutter. Alle varer er forseglet, serienummerkontrollert og dekket av 24 måneders garanti.Forseglet, 24 måneders garanti.

Overvåkingsliste Logg inn
Black standalone SATA duplicator with 16x2 LCD and eleven drive slots

EZ Dupe, Inc.

EZ Dupe, Inc. H11HSATB 1-to-11 SATA Duplicator

SKU CH-TFS8-FJK3B

Standalone SATA duplicator copies up to 11 drives at 150 MB/s with four copy and four erase modes including DoD 5220.22 standards

  • TypeHard Drive Duplicator
  • Panel ColorBlack
  • Operating TypeStandalone
  • Display16 x 2 LCD
  • ConnectorSATA
  • Target1 to 11

Target 1 to 11

Data Transfer Rate 150MB/s

Overstrøkne versjoner finnes, men er ikke på lager her.

  • Copy 11 drives simultaneously at 150 MB/s per slot
  • Four copy modes include quick, full, partitioned and percentage copy
  • Four erase modes include quick, full, DoD 3-pass and DoD 7-pass
  • Supports 2.5" and 3.5" SATA drives without adapters
  • Standalone operation with 16×2 LCD and 128 MB buffer

Duplication capacity and standalone operation

The duplicator copies one source drive to as many as eleven target drives simultaneously using SATA connectors for both 2.5 and 3.5 inch hard disks and solid state drives. Operation is completely standalone with a sixteen by two LCD and indicator lights, so no host computer or software is required during the copy or erase process.

Sustained throughput and erase compliance

Each target slot maintains a transfer rate of one hundred fifty megabytes per second, which equals nine gigabytes per minute, across all eleven ports during extended duplication runs. Four erase modes are available including three pass and seven pass methods that follow the 5220.22 standard for defence grade sanitisation.

Power and drive preparation checklist

Verify that the installation site can supply alternating current between one hundred fifteen and two hundred thirty volts at fifty or sixty hertz. Confirm that every source and target drive uses a SATA interface and fits the 2.5 or 3.5 inch form factor, because no adapter is included for other connector types.

Høydepunkter

  • Copy 11 drives simultaneously at 150 MB/s per slot
  • Four copy modes include quick, full, partitioned and percentage copy
  • Four erase modes include quick, full, DoD 3-pass and DoD 7-pass
  • Supports 2.5" and 3.5" SATA drives without adapters
  • Standalone operation with 16×2 LCD and 128 MB buffer

Spesifikasjoner

BrandEZ Dupe
TypeHard Drive Duplicator
ModelH11HSATB
Part NumberH11HSATB
Panel ColorBlack
Operating TypeStandalone
Display16 x 2 LCD
ConnectorSATA
Target1 to 11
Buffer Memory128M
ControllerAthena Controller
Supported MediaSATA Hard Drive Disk / SATA Solid State Drives
Data Transfer Rate150MB/s
Load TypeSlot
Key FeaturesDuplication
FeaturesIndication Lights
Power SupplyAC: 115-230 V, 50/60 Hz

Andre versjoner av denne modellen

5 flere i samme serie

Samme familie, annet minne, annen kjøler eller klokkefrekvens — sammenlign før du bestemmer deg.

Spørsmål om denne varen

How loud or hot does the H11HSATB get when running all 11 bays at 150 MB/s for hours?

The duplicator is a standalone unit with an AC 115-230 V, 50/60 Hz power supply; no fan noise or thermal figures are published.

What must I already own so the duplicator can copy drives right away?

You need a master SATA drive and up to 11 target SATA 3.5" or 2.5" drives; no computer, software or adapter is required.

Will the Athena Controller work with older SATA I or II drives I still keep?

The controller accepts any SATA-interfaced 3.5" or 2.5" HDD or SSD without an adapter; legacy SATA revisions are supported.

Også i denne avdelingen

Kunder sammenlignet disse

Samme hylle, samme kasse — åtte mynter og 30 minutters kurslås.