Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Grey thermal pad sheet 80 by 40 by 0.5 mm

GELID SOLUTIONS

GELID SOLUTIONS GP-Extreme 12W Thermal Pad 80x40x0.5mm

SKU CH-J7YM-EG3C6

High-conductivity 12 W/mK thermal pad measuring 80×40×0.5 mm for memory ICs, MOSFETs and other SMD components

Option 80 x 40 x 0.5 mm

  • 12 W/mK thermal conductivity transfers heat efficiently from memory and chipset components
  • 5 mm thickness conforms to uneven PCB surfaces for reliable contact
  • Non-electrically conductive material prevents short circuits on dense boards
  • 80 × 40 mm sheet covers large VGA card or laptop heatsink areas
  • Soft, non-curing pad installs easily without hardening over time

Thermal pad for uneven PCB surfaces

The GELID SOLUTIONS GP-Extreme is a 12 W/mK thermal pad measuring 80 by 40 by 0.5 mm. It targets builders who need reliable heat transfer between a heatsink and components that sit at different heights on a circuit board. The material is non-electrically conductive, non-corrosive, non-curing and non-toxic. It suits graphics cards, laptops, consoles and dense SMD layouts.

Softness and pre-cut dimensions simplify

The pad’s softness lets it conform to surface irregularities without excessive pressure, filling gaps that firmer pads would leave. Its 80 by 40 mm footprint matches larger PCB areas so users can apply a single piece instead of cutting smaller strips. No adhesive or curing time is required; the pad stays pliable and can be repositioned during assembly.

0.5 mm thickness decides fit for tight clearances

This variant is 0.5 mm thick; the same series also exists in 1.0, 1.5, 2.0 and 3.0 mm options. Choose this thickness only when the component-to-heatsink gap measures close to half a millimetre. Buyers needing to bridge larger gaps should select a thicker pad from the same range.

Põhijooned

  • 12 W/mK thermal conductivity transfers heat efficiently from memory and chipset components
  • 5 mm thickness conforms to uneven PCB surfaces for reliable contact
  • Non-electrically conductive material prevents short circuits on dense boards
  • 80 × 40 mm sheet covers large VGA card or laptop heatsink areas
  • Soft, non-curing pad installs easily without hardening over time

Tehnilised andmed

BrandGELID Solutions

Selle mudeli teised versioonid

4 veel samast sarjast

Sama seeria, erinev mälumaht, jahutus või taktsagedus — võrrelge enne otsustamist.

Küsimused selle toote kohta

When will the 0.5 mm GP-Extreme pad need replacing?

The pad is non-hardening and non-curing, so it does not degrade on a fixed schedule. Replace only if the cooler is removed or the pad is physically damaged.

What limits heat transfer during long sessions with this 12 W/mK pad?

The 12 W/mK conductivity and 0.5 mm thickness set the steady-state thermal resistance; the pad itself does not saturate or throttle.

Does the GP-Extreme pad generate noise or extra heat when used continuously?

It is a passive silicone pad with no moving parts, so it produces zero noise and adds no heat beyond conducting it from the component to the heatsink.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.