Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Grey rectangular thermal pad 85 by 45 by 1.5 mm

Lirealar

Lirealar Extreme Odyssey Thermal Pad 12.8 W/mK 85x45x1.5mm

SKU CH-KKTE-R5D41

High-conductivity 12.8 W/mK silicone pad transfers heat from CPUs, GPUs or laptop heatsinks while remaining electrically insulating and reusable

  • Thermal Conductivity12.8 W/mK

Size 85x45x1.5mm

Läbikriipsutatud versioonid on olemas, kuid neid pole siin saadaval.

  • High thermal conductivity of 12.8 W/mK moves heat efficiently
  • Non-conductive silicone prevents electrical shorts on components
  • Non-corrosive and non-curing material stays stable over time
  • Natural viscosity allows easy installation and reusability
  • 85x45x1.5mm size fits laptop heatsinks, GPU and CPU coolers

Precision Thermal Pad for GPU and Laptop Repairs

This 85 by 45 millimetre pad uses 12.8 W/mK silicone to bridge gaps between chips and heatsinks in laptops, graphics cards and LED coolers. It is non-conductive, non-corrosive and non-curing, so it will not short nearby components or degrade over time. The material stays pliable for repeated disassembly.

Replaces Dried Paste or Thin Stock Pads

Swap this in when factory thermal paste has hardened or when a 0.5 millimetre pad leaves a visible gap on uneven surfaces. The 1.5 millimetre thickness fills larger tolerances on memory modules, VRM arrays and CPU dies where thinner interfaces cannot make full contact. It is not suited for builds that need a sub-millimetre bond line.

Simple Press-Fit Install With No Mess

Peel the protective film, place the pad on the die and mount the cooler; natural viscosity holds it in position without spreading. Avoid stretching the sheet or stacking multiple layers, as both reduce thermal transfer. The pad can be lifted and repositioned during fitting, but repeated handling will eventually weaken the surface tack.

Põhijooned

  • High thermal conductivity of 12.8 W/mK moves heat efficiently
  • Non-conductive silicone prevents electrical shorts on components
  • Non-corrosive and non-curing material stays stable over time
  • Natural viscosity allows easy installation and reusability
  • 85x45x1.5mm size fits laptop heatsinks, GPU and CPU coolers

Tehnilised andmed

Thermal Conductivity12.8 W/mK

Selle mudeli teised versioonid

5 veel samast sarjast

Sama seeria, erinev mälumaht, jahutus või taktsagedus — võrrelge enne otsustamist.

Küsimused selle toote kohta

Will the 85x45x1.5mm pad cover my GPU die and surrounding components?

The pad measures 85 by 45 millimetres with a 1.5 millimetre thickness; trim it with scissors if your die area is smaller.

How do I install the pad without trapping air bubbles?

Clean both surfaces with isopropyl alcohol, peel the protective film, place the pad flat, then press the heatsink down evenly — do not slide it.

When should I replace this thermal pad?

Replace it whenever you disassemble the cooler or if temperatures rise noticeably; the non-curing silicone stays pliable but loses performance after repeated compression cycles.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.