Kripto para kabul ediyoruz — böylece elinizdeki koinlerle gerçek donanım alabilirsiniz.Kripto parayla ödeyin, onu gerçek donanıma harcayın. $399 üzeri siparişlerde dünya genelinde sigortalı kargo ücretsizdir. Sade, markasız koliler Almanya’dan gönderilir.$399 üzeri siparişlerde sigortalı kargo ücretsizdir. Ödeme sayfası açıldığında kurunuz 30 dakika kilitli kalır.Kur 30 dakika kilitli. Her ürün mühürlüdür, seri numarası kontrol edilir ve 24 ay garanti kapsamındadır.Mühürlü, 24 ay garantili.

Favori ürünler Giriş yap
Grey rectangular thermal pad 85 by 45 by 1.5 mm

Lirealar

Lirealar Extreme Odyssey Thermal Pad 12.8 W/mK 85x45x1.5mm

SKU CH-KKTE-R5D41

High-conductivity 12.8 W/mK silicone pad transfers heat from CPUs, GPUs or laptop heatsinks while remaining electrically insulating and reusable

  • Thermal Conductivity12.8 W/mK

Size 85x45x1.5mm

Üzeri çizili sürümler mevcuttur ancak burada stokta değildir.

  • High thermal conductivity of 12.8 W/mK moves heat efficiently
  • Non-conductive silicone prevents electrical shorts on components
  • Non-corrosive and non-curing material stays stable over time
  • Natural viscosity allows easy installation and reusability
  • 85x45x1.5mm size fits laptop heatsinks, GPU and CPU coolers

Precision Thermal Pad for GPU and Laptop Repairs

This 85 by 45 millimetre pad uses 12.8 W/mK silicone to bridge gaps between chips and heatsinks in laptops, graphics cards and LED coolers. It is non-conductive, non-corrosive and non-curing, so it will not short nearby components or degrade over time. The material stays pliable for repeated disassembly.

Replaces Dried Paste or Thin Stock Pads

Swap this in when factory thermal paste has hardened or when a 0.5 millimetre pad leaves a visible gap on uneven surfaces. The 1.5 millimetre thickness fills larger tolerances on memory modules, VRM arrays and CPU dies where thinner interfaces cannot make full contact. It is not suited for builds that need a sub-millimetre bond line.

Simple Press-Fit Install With No Mess

Peel the protective film, place the pad on the die and mount the cooler; natural viscosity holds it in position without spreading. Avoid stretching the sheet or stacking multiple layers, as both reduce thermal transfer. The pad can be lifted and repositioned during fitting, but repeated handling will eventually weaken the surface tack.

Öne çıkanlar

  • High thermal conductivity of 12.8 W/mK moves heat efficiently
  • Non-conductive silicone prevents electrical shorts on components
  • Non-corrosive and non-curing material stays stable over time
  • Natural viscosity allows easy installation and reusability
  • 85x45x1.5mm size fits laptop heatsinks, GPU and CPU coolers

Teknik özellikler

Thermal Conductivity12.8 W/mK

Bu modelin diğer sürümleri

Aynı seriden 5 tane daha

Aynı aile, farklı bellek, soğutucu veya frekans — karar vermeden önce karşılaştırın.

Bu ürünle ilgili sorular

Will the 85x45x1.5mm pad cover my GPU die and surrounding components?

The pad measures 85 by 45 millimetres with a 1.5 millimetre thickness; trim it with scissors if your die area is smaller.

How do I install the pad without trapping air bubbles?

Clean both surfaces with isopropyl alcohol, peel the protective film, place the pad flat, then press the heatsink down evenly — do not slide it.

When should I replace this thermal pad?

Replace it whenever you disassemble the cooler or if temperatures rise noticeably; the non-curing silicone stays pliable but loses performance after repeated compression cycles.

Bu reyondan diğerleri

Müşteriler bunları karşılaştırdı

Aynı raf, aynı sipariş tamamlama — sekiz koin ve 30 dakikalık kur kilidi.