Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Two carbon-grey 6+2-pin cables with 144×.5 mm RGB braided sleeve

myVolts

myVolts RGB Cable Kit 2×6+2-Pin 144×.5 mm power supply

SKU CH-4D3V-1VMQK

Addressable RGB extension cables with 144×.5 mm fibre braid and dual 6+2-pin connectors for 5 V motherboard sync

  • TypeAT
  • Addressable RGB lighting syncs with 5 V motherboard headers
  • Dual 6+2-pin connectors power GPU and light strip together
  • 144×.5 mm fibre braid diffuses light evenly across the case
  • Carbon-grey extension cable routes cleanly behind the motherboard tray
  • Multiple preset effects include streamer, gradient and single-colour modes

myVolts RGB Cable Kit 2×6+2-Pin

This cable kit adds addressable RGB lighting to a PC build using two 6+2-pin connectors. It is designed for enthusiasts who want a neon light effect inside a side-transparent chassis. The kit combines a carbon grey extension cable with a 144×.5 mm fiber braided net that emits light.

Upgrade from standard power cables

The kit replaces plain 6+2-pin power cables with an illuminated version that also delivers power to the graphics card. The visual jump is worth it when the motherboard has a 5 V addressable RGB header and the builder wants a waterfall-style light flow across the hardware. It does not suit systems limited to 12 V RGB headers or those without an ARGB connector.

Installation and common issues

Connection is straightforward: plug the 5 V ARGB lead into the motherboard's addressable RGB header and attach the 6+2-pin ends to the graphics card. The most frequent error is using a 12 V RGB controller or 12 V 4-pin header, which will burn the kit. Builders must confirm the motherboard supports 5 V ARGB before installing.

Põhijooned

  • Addressable RGB lighting syncs with 5 V motherboard headers
  • Dual 6+2-pin connectors power GPU and light strip together
  • 144×.5 mm fibre braid diffuses light evenly across the case
  • Carbon-grey extension cable routes cleanly behind the motherboard tray
  • Multiple preset effects include streamer, gradient and single-colour modes

Tehnilised andmed

TypeAT

Küsimused selle toote kohta

What clearance does the 144×.5 mm braided net need inside the case?

The fiber braided net measures 144 by 0.5 mm, so allow at least that width and height in the cable routing channel for a clean fit.

Which motherboard header do I plug the 2×6+2-Pin connectors into, and what is the common mistake?

Connect only to a 5 V addressable RGB header; using a 12 V 4-pin header or controller will burn the cable.

When should I replace the carbon gray extension layer?

Replace it if the insulation cracks, pins bend, or the braided net frays enough to expose conductors.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.