Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Two carbon-grey 6+2-pin cables with 144×.5 mm RGB braided sleeve

myVolts

myVolts RGB Cable Kit 2×6+2-Pin 144×.5 mm power supply

SKU CH-4D3V-1VMQK

Addressable RGB extension cables with 144×.5 mm fibre braid and dual 6+2-pin connectors for 5 V motherboard sync

  • TypeAT
  • Addressable RGB lighting syncs with 5 V motherboard headers
  • Dual 6+2-pin connectors power GPU and light strip together
  • 144×.5 mm fibre braid diffuses light evenly across the case
  • Carbon-grey extension cable routes cleanly behind the motherboard tray
  • Multiple preset effects include streamer, gradient and single-colour modes

myVolts RGB Cable Kit 2×6+2-Pin

This cable kit adds addressable RGB lighting to a PC build using two 6+2-pin connectors. It is designed for enthusiasts who want a neon light effect inside a side-transparent chassis. The kit combines a carbon grey extension cable with a 144×.5 mm fiber braided net that emits light.

Upgrade from standard power cables

The kit replaces plain 6+2-pin power cables with an illuminated version that also delivers power to the graphics card. The visual jump is worth it when the motherboard has a 5 V addressable RGB header and the builder wants a waterfall-style light flow across the hardware. It does not suit systems limited to 12 V RGB headers or those without an ARGB connector.

Installation and common issues

Connection is straightforward: plug the 5 V ARGB lead into the motherboard's addressable RGB header and attach the 6+2-pin ends to the graphics card. The most frequent error is using a 12 V RGB controller or 12 V 4-pin header, which will burn the kit. Builders must confirm the motherboard supports 5 V ARGB before installing.

Helstu kostir

  • Addressable RGB lighting syncs with 5 V motherboard headers
  • Dual 6+2-pin connectors power GPU and light strip together
  • 144×.5 mm fibre braid diffuses light evenly across the case
  • Carbon-grey extension cable routes cleanly behind the motherboard tray
  • Multiple preset effects include streamer, gradient and single-colour modes

Tæknilýsing

TypeAT

Spurningar um þessa vöru

What clearance does the 144×.5 mm braided net need inside the case?

The fiber braided net measures 144 by 0.5 mm, so allow at least that width and height in the cable routing channel for a clean fit.

Which motherboard header do I plug the 2×6+2-Pin connectors into, and what is the common mistake?

Connect only to a 5 V addressable RGB header; using a 12 V 4-pin header or controller will burn the cable.

When should I replace the carbon gray extension layer?

Replace it if the insulation cracks, pins bend, or the braided net frays enough to expose conductors.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.