Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Two carbon-grey 6+2-pin cables with 144×.5 mm RGB braided sleeve

myVolts

myVolts RGB Cable Kit 2×6+2-Pin 144×.5 mm power supply

SKU CH-4D3V-1VMQK

Addressable RGB extension cables with 144×.5 mm fibre braid and dual 6+2-pin connectors for 5 V motherboard sync

  • TypeAT
  • Addressable RGB lighting syncs with 5 V motherboard headers
  • Dual 6+2-pin connectors power GPU and light strip together
  • 144×.5 mm fibre braid diffuses light evenly across the case
  • Carbon-grey extension cable routes cleanly behind the motherboard tray
  • Multiple preset effects include streamer, gradient and single-colour modes

myVolts RGB Cable Kit 2×6+2-Pin

This cable kit adds addressable RGB lighting to a PC build using two 6+2-pin connectors. It is designed for enthusiasts who want a neon light effect inside a side-transparent chassis. The kit combines a carbon grey extension cable with a 144×.5 mm fiber braided net that emits light.

Upgrade from standard power cables

The kit replaces plain 6+2-pin power cables with an illuminated version that also delivers power to the graphics card. The visual jump is worth it when the motherboard has a 5 V addressable RGB header and the builder wants a waterfall-style light flow across the hardware. It does not suit systems limited to 12 V RGB headers or those without an ARGB connector.

Installation and common issues

Connection is straightforward: plug the 5 V ARGB lead into the motherboard's addressable RGB header and attach the 6+2-pin ends to the graphics card. The most frequent error is using a 12 V RGB controller or 12 V 4-pin header, which will burn the kit. Builders must confirm the motherboard supports 5 V ARGB before installing.

Kohokohdat

  • Addressable RGB lighting syncs with 5 V motherboard headers
  • Dual 6+2-pin connectors power GPU and light strip together
  • 144×.5 mm fibre braid diffuses light evenly across the case
  • Carbon-grey extension cable routes cleanly behind the motherboard tray
  • Multiple preset effects include streamer, gradient and single-colour modes

Tekniset tiedot

TypeAT

Kysymyksiä tästä tuotteesta

What clearance does the 144×.5 mm braided net need inside the case?

The fiber braided net measures 144 by 0.5 mm, so allow at least that width and height in the cable routing channel for a clean fit.

Which motherboard header do I plug the 2×6+2-Pin connectors into, and what is the common mistake?

Connect only to a 5 V addressable RGB header; using a 12 V 4-pin header or controller will burn the cable.

When should I replace the carbon gray extension layer?

Replace it if the insulation cracks, pins bend, or the braided net frays enough to expose conductors.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.