Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Black 9 cm square cooling fan with 2 pin power connector

OEM Industries

OEM Industries MMF-09D24TS RN9 9CM 24V 0.19A CPU cooler

SKU CH-EXMZ-2552K

A 9 cm dual-ball-bearing fan runs on 24 V and draws 0.19 A through a two-pin connector

  • ColorBlack
  • TypeFan only
  • Fan Size9CM
  • Bearing Type2 Ball
  • Power Connector2 Pin
  • Original Melco manufacturing ensures reliable industrial-grade operation
  • 9 cm square frame fits standard 90 mm mounting patterns
  • 24 V 0.19 A rating matches PLC and inverter power rails
  • Dual ball bearing design extends service life in continuous duty
  • Two-pin connector simplifies wiring for ABB and Yaskawa equipment

Compact 9 cm fan for industrial boards

This 90 mm square by 25 mm thick fan runs on 24 V DC at 0.19 A and uses a two-pin connector. It is built for PLC and inverter cabinets such as ABB and Yaskawa units where a small, reliable airflow source is required. The black frame fits tight equipment bays. Buyers needing a larger frame or a different voltage should look elsewhere.

Dual ball bearings for continuous duty

Two ball bearings keep the rotor stable during non-stop operation in warm enclosures. The bearing choice reduces wear compared with sleeve designs when the fan runs 24/7. No speed-control wire is present, so the fan spins at a fixed rate whenever power is applied. Installations that require PWM regulation or tachometer feedback cannot use this model.

Check voltage and mounting before ordering

Verify that your system supplies 24 V DC and provides a two-pin header with the correct polarity. The 90 mm hole spacing must match the chassis cut-out. No screws, guards or adapters are included in the package. Systems expecting a three-pin or four-pin connector will need a different fan.

Põhijooned

  • Original Melco manufacturing ensures reliable industrial-grade operation
  • 9 cm square frame fits standard 90 mm mounting patterns
  • 24 V 0.19 A rating matches PLC and inverter power rails
  • Dual ball bearing design extends service life in continuous duty
  • Two-pin connector simplifies wiring for ABB and Yaskawa equipment

Tehnilised andmed

ModelMMF-09D24TS RN9
ColorBlack
TypeFan only
Fan Size9CM
Bearing Type2 Ball
Power Connector2 Pin

Küsimused selle toote kohta

How much heat and noise does the 9 cm 24 V 0.19 A fan produce when running continuously?

The fan draws 0.19 A at 24 V, so its power dissipation is low; the dual ball bearing is rated for long life and runs quietly at typical speeds for a 90 mm frame.

What power source and connector does the MMF-09D24TS RN9 need to operate?

It requires a 24 V DC supply and a 2-pin header that matches the 2-wire plug on the fan.

Will this 90 mm 25 mm thick fan fit the same mounting holes as the older PLC or inverter fan I am replacing?

The 90 mm square frame and 25 mm thickness match the standard footprint used on many ABB and Yaskawa devices, so it aligns with the original mounting pattern.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.