Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Black 9 cm square cooling fan with 2 pin power connector

OEM Industries

OEM Industries MMF-09D24TS RN9 9CM 24V 0.19A CPU cooler

SKU CH-EXMZ-2552K

A 9 cm dual-ball-bearing fan runs on 24 V and draws 0.19 A through a two-pin connector

  • ColorBlack
  • TypeFan only
  • Fan Size9CM
  • Bearing Type2 Ball
  • Power Connector2 Pin
  • Original Melco manufacturing ensures reliable industrial-grade operation
  • 9 cm square frame fits standard 90 mm mounting patterns
  • 24 V 0.19 A rating matches PLC and inverter power rails
  • Dual ball bearing design extends service life in continuous duty
  • Two-pin connector simplifies wiring for ABB and Yaskawa equipment

Compact 9 cm fan for industrial boards

This 90 mm square by 25 mm thick fan runs on 24 V DC at 0.19 A and uses a two-pin connector. It is built for PLC and inverter cabinets such as ABB and Yaskawa units where a small, reliable airflow source is required. The black frame fits tight equipment bays. Buyers needing a larger frame or a different voltage should look elsewhere.

Dual ball bearings for continuous duty

Two ball bearings keep the rotor stable during non-stop operation in warm enclosures. The bearing choice reduces wear compared with sleeve designs when the fan runs 24/7. No speed-control wire is present, so the fan spins at a fixed rate whenever power is applied. Installations that require PWM regulation or tachometer feedback cannot use this model.

Check voltage and mounting before ordering

Verify that your system supplies 24 V DC and provides a two-pin header with the correct polarity. The 90 mm hole spacing must match the chassis cut-out. No screws, guards or adapters are included in the package. Systems expecting a three-pin or four-pin connector will need a different fan.

Přednosti

  • Original Melco manufacturing ensures reliable industrial-grade operation
  • 9 cm square frame fits standard 90 mm mounting patterns
  • 24 V 0.19 A rating matches PLC and inverter power rails
  • Dual ball bearing design extends service life in continuous duty
  • Two-pin connector simplifies wiring for ABB and Yaskawa equipment

Specifikace

ModelMMF-09D24TS RN9
ColorBlack
TypeFan only
Fan Size9CM
Bearing Type2 Ball
Power Connector2 Pin

Otázky k tomuto produktu

How much heat and noise does the 9 cm 24 V 0.19 A fan produce when running continuously?

The fan draws 0.19 A at 24 V, so its power dissipation is low; the dual ball bearing is rated for long life and runs quietly at typical speeds for a 90 mm frame.

What power source and connector does the MMF-09D24TS RN9 need to operate?

It requires a 24 V DC supply and a 2-pin header that matches the 2-wire plug on the fan.

Will this 90 mm 25 mm thick fan fit the same mounting holes as the older PLC or inverter fan I am replacing?

The 90 mm square frame and 25 mm thickness match the standard footprint used on many ABB and Yaskawa devices, so it aligns with the original mounting pattern.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.