Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Black 9 cm square cooling fan with 2 pin power connector

OEM Industries

OEM Industries MMF-09D24TS RN9 9CM 24V 0.19A CPU cooler

SKU CH-EXMZ-2552K

A 9 cm dual-ball-bearing fan runs on 24 V and draws 0.19 A through a two-pin connector

  • ColorBlack
  • TypeFan only
  • Fan Size9CM
  • Bearing Type2 Ball
  • Power Connector2 Pin
  • Original Melco manufacturing ensures reliable industrial-grade operation
  • 9 cm square frame fits standard 90 mm mounting patterns
  • 24 V 0.19 A rating matches PLC and inverter power rails
  • Dual ball bearing design extends service life in continuous duty
  • Two-pin connector simplifies wiring for ABB and Yaskawa equipment

Compact 9 cm fan for industrial boards

This 90 mm square by 25 mm thick fan runs on 24 V DC at 0.19 A and uses a two-pin connector. It is built for PLC and inverter cabinets such as ABB and Yaskawa units where a small, reliable airflow source is required. The black frame fits tight equipment bays. Buyers needing a larger frame or a different voltage should look elsewhere.

Dual ball bearings for continuous duty

Two ball bearings keep the rotor stable during non-stop operation in warm enclosures. The bearing choice reduces wear compared with sleeve designs when the fan runs 24/7. No speed-control wire is present, so the fan spins at a fixed rate whenever power is applied. Installations that require PWM regulation or tachometer feedback cannot use this model.

Check voltage and mounting before ordering

Verify that your system supplies 24 V DC and provides a two-pin header with the correct polarity. The 90 mm hole spacing must match the chassis cut-out. No screws, guards or adapters are included in the package. Systems expecting a three-pin or four-pin connector will need a different fan.

Kohokohdat

  • Original Melco manufacturing ensures reliable industrial-grade operation
  • 9 cm square frame fits standard 90 mm mounting patterns
  • 24 V 0.19 A rating matches PLC and inverter power rails
  • Dual ball bearing design extends service life in continuous duty
  • Two-pin connector simplifies wiring for ABB and Yaskawa equipment

Tekniset tiedot

ModelMMF-09D24TS RN9
ColorBlack
TypeFan only
Fan Size9CM
Bearing Type2 Ball
Power Connector2 Pin

Kysymyksiä tästä tuotteesta

How much heat and noise does the 9 cm 24 V 0.19 A fan produce when running continuously?

The fan draws 0.19 A at 24 V, so its power dissipation is low; the dual ball bearing is rated for long life and runs quietly at typical speeds for a 90 mm frame.

What power source and connector does the MMF-09D24TS RN9 need to operate?

It requires a 24 V DC supply and a 2-pin header that matches the 2-wire plug on the fan.

Will this 90 mm 25 mm thick fan fit the same mounting holes as the older PLC or inverter fan I am replacing?

The 90 mm square frame and 25 mm thickness match the standard footprint used on many ABB and Yaskawa devices, so it aligns with the original mounting pattern.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.