Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Small frameless graphics card cooler, brown and transparent finish, three mounting holes, three-pin power connector

OEM Industries

OEM Industries PLD10010S12M 12V 0.2A 3 Pin VGA Fan Graphics Card Cooler

SKU CH-8WSD-K7P9J

Replacement graphics card fan with a 12 V 0.2 A three-pin connector, sleeve bearing and 39 mm mounting spacing

  • Color2-Tone
  • TypeAccessories
  • Bearing TypeSleeve Bearing
  • Power Connector3 Pin
  • 12 V 0.2 A low power draw keeps card temperatures down
  • sleeve bearing runs quietly for everyday desktop use
  • 3 pin connector fits standard graphics card headers
  • 95 mm frameless design suits tight GPU clearances
  • 39 mm mounting pattern matches listed Gigabyte models

Replacement VGA Fan for Gigabyte Cards

This 12V 0.2A three-pin fan fits Gigabyte models such as the GVN550WF2, N56GOC, R667D3, R777OC, GV-N560OC-1GI, GTX560Ti and GTX660Ti. It uses a sleeve bearing and a frameless brown and transparent housing. The cooler mounts with three holes on a 39mm pitch and has a 95mm diameter.

Upgrading from a Worn Original Cooler

Replace the factory fan when bearings become noisy, airflow drops or the card throttles under load. The three-wire connector restores speed reporting so the GPU driver can regulate temperature. The jump is worth it when the original cooler still spins but no longer keeps the core within safe limits.

Check Mounting Holes and Connector Before Ordering

Verify that your card uses the three-hole 39mm pattern and a standard three-pin header. The frameless design means no screw holes on the fan frame itself; the shroud must provide the mounting points. Confirm the 95mm diameter clears adjacent components on your specific board layout.

Põhijooned

  • 12 V 0.2 A low power draw keeps card temperatures down
  • sleeve bearing runs quietly for everyday desktop use
  • 3 pin connector fits standard graphics card headers
  • 95 mm frameless design suits tight GPU clearances
  • 39 mm mounting pattern matches listed Gigabyte models

Tehnilised andmed

ModelPLD10010S12M
Color2-Tone
TypeAccessories
Bearing TypeSleeve Bearing
Power Connector3 Pin

Küsimused selle toote kohta

What are the mounting hole dimensions and spacing for the PLD10010S12M cooler?

The cooler uses three mounting holes with a 39 mm spacing between each hole.

How do I connect the 3-pin power connector, and what mistake should I avoid?

Plug the 3-pin connector into the graphics card's fan header; do not force it onto a 4-pin PWM header as the keying differs.

When should I replace the sleeve bearing fan in this cooler?

Replace the fan when bearing noise becomes audible or RPM drops below the rated 0.2 A draw at 12 V.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.