Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Small frameless graphics card cooler, brown and transparent finish, three mounting holes, three-pin power connector

OEM Industries

OEM Industries PLD10010S12M 12V 0.2A 3 Pin VGA Fan Graphics Card Cooler

SKU CH-8WSD-K7P9J

Replacement graphics card fan with a 12 V 0.2 A three-pin connector, sleeve bearing and 39 mm mounting spacing

  • Color2-Tone
  • TypeAccessories
  • Bearing TypeSleeve Bearing
  • Power Connector3 Pin
  • 12 V 0.2 A low power draw keeps card temperatures down
  • sleeve bearing runs quietly for everyday desktop use
  • 3 pin connector fits standard graphics card headers
  • 95 mm frameless design suits tight GPU clearances
  • 39 mm mounting pattern matches listed Gigabyte models

Replacement VGA Fan for Gigabyte Cards

This 12V 0.2A three-pin fan fits Gigabyte models such as the GVN550WF2, N56GOC, R667D3, R777OC, GV-N560OC-1GI, GTX560Ti and GTX660Ti. It uses a sleeve bearing and a frameless brown and transparent housing. The cooler mounts with three holes on a 39mm pitch and has a 95mm diameter.

Upgrading from a Worn Original Cooler

Replace the factory fan when bearings become noisy, airflow drops or the card throttles under load. The three-wire connector restores speed reporting so the GPU driver can regulate temperature. The jump is worth it when the original cooler still spins but no longer keeps the core within safe limits.

Check Mounting Holes and Connector Before Ordering

Verify that your card uses the three-hole 39mm pattern and a standard three-pin header. The frameless design means no screw holes on the fan frame itself; the shroud must provide the mounting points. Confirm the 95mm diameter clears adjacent components on your specific board layout.

Helstu kostir

  • 12 V 0.2 A low power draw keeps card temperatures down
  • sleeve bearing runs quietly for everyday desktop use
  • 3 pin connector fits standard graphics card headers
  • 95 mm frameless design suits tight GPU clearances
  • 39 mm mounting pattern matches listed Gigabyte models

Tæknilýsing

ModelPLD10010S12M
Color2-Tone
TypeAccessories
Bearing TypeSleeve Bearing
Power Connector3 Pin

Spurningar um þessa vöru

What are the mounting hole dimensions and spacing for the PLD10010S12M cooler?

The cooler uses three mounting holes with a 39 mm spacing between each hole.

How do I connect the 3-pin power connector, and what mistake should I avoid?

Plug the 3-pin connector into the graphics card's fan header; do not force it onto a 4-pin PWM header as the keying differs.

When should I replace the sleeve bearing fan in this cooler?

Replace the fan when bearing noise becomes audible or RPM drops below the rated 0.2 A draw at 12 V.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.