Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Black 30mm square micro fan with two wires and a 2-pin connector

OEM Industries

OEM Industries SF30C-12 30mm 12V 0.06A 2 Pin Micro Fan

SKU CH-2283-GZCR9

30 mm ball-bearing micro fan runs on 12 V at 0.06 A with a two-pin connector

  • ColorBlack
  • TypeFan only
  • Fan Size30mm
  • Bearing TypeBall
  • Power Connector2 Pin
  • Compact 30 mm micro fan fits tight Raspberry Pi cases
  • 12 V 0.06 A draw keeps power use minimal
  • Ball bearing design extends operating life
  • Two-pin connector enables simple plug-in installation
  • Black low-profile frame blends with board aesthetics

Compact 30 mm Micro Fan for Tight Builds

The OEM Industries SF30C-12 is a 30 mm square micro fan that runs on 12 V and draws 0.06 A through a two-pin connector. Its ball bearing and 30 mm frame suit small-form-factor cases, embedded boards and similar space-constrained cooling tasks.

Suited for Low-Profile Airflow.

Makers adding spot cooling to a Raspberry Pi or similar single-board computer will find the dimensions and voltage a direct match. Builders who need strong static pressure for dense heatsinks or high-wattage CPUs should look at larger fans with higher airflow ratings.

Handles Modest Heat Loads in Confined Spaces

The fan moves enough air for low-power SoCs, router boards or auxiliary component cooling where space is at a premium. It runs out of headroom when tasked with cooling a mainstream desktop processor or any load that demands sustained high-volume airflow.

Põhijooned

  • Compact 30 mm micro fan fits tight Raspberry Pi cases
  • 12 V 0.06 A draw keeps power use minimal
  • Ball bearing design extends operating life
  • Two-pin connector enables simple plug-in installation
  • Black low-profile frame blends with board aesthetics

Tehnilised andmed

ModelSF30C-12
ColorBlack
TypeFan only
Fan Size30mm
Bearing TypeBall
Power Connector2 Pin

Küsimused selle toote kohta

What power supply must I already have to run the 12 V SF30C-12 fan?

You need a source that can deliver 12 V at least 0.06 A; the fan draws 12 V and 0.06 A from its 2 pin connector.

Can the 30 mm ball bearing fan fit in the same space as an older 30 mm sleeve bearing unit?

Yes, the SF30C-12 shares the 30 mm frame size, so it occupies the same mounting footprint as other 30 mm fans.

How can I verify the SF30C-12 is spinning correctly after wiring it to 12 V?

Apply 12 V to the 2 pin leads; the ball bearing fan should start immediately and run smoothly without audible rattling.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.