Me võtame vastu krüptoraha — nii saab teie hoitav krüptoraha osta päris riistvara.Makske krüptorahaga, kulutage seda päris riistvarale. Tasuta kindlustatud tarne kogu maailmas, üle 399 $. Lihtsad, kaubamärgita väliskarbid, saadetud Saksamaalt.Tasuta kindlustatud tarne üle 399 $. Teie kurss lukustatakse 30 minutiks kohe, kui kassa avaneb.Kurss lukustatud 30 minutiks. Iga toode on pitseeritud, selle seerianumber on kontrollitud ja sellel kehtib 24-kuuline garantii.Pitseeritud, 24-kuulise garantiiga.

Hinnavaatlus Logi sisse
Green rectangular development board with USB-C, Qw/ST and debug connectors, reset and BOOT buttons, clear pin labels

Pimoroni

Pimoroni Pico Plus 2 RP2350 16MB flash 8MB PSRAM development board

SKU CH-7XK8-7T4EM

Development board with dual Arm Cortex-M33 cores at 150 MHz, 16 MB flash, 8 MB PSRAM, USB-C, Qw/ST, SP/CE and debug connectors

Name Pico Plus 2

  • Pico Plus 2 W
  • Pico Plus 2

Läbikriipsutatud versioonid on olemas, kuid neid pole siin saadaval.

  • Dual Arm Cortex-M33 cores reach 150 MHz for responsive edge processing
  • 16 MB QSPI flash supports execute-in-place for large firmware images
  • 8 MB PSRAM expands runtime memory for data-heavy applications
  • USB-C provides power, programming and data through one cable
  • Qw/ST, SP/CE and debug connectors enable solderless add-ons and SWD access

Pico Plus 2 RP2350 for embedded developers

The Pimoroni Pico Plus 2 is a microcontroller board built around the RP2350B dual Arm Cortex M33 processor running at up to 150MHz with 520KB of SRAM. It targets makers and engineers who need generous on-board storage and quick peripheral expansion without soldering.

Qw/ST and SP/CE connectors enable solderless

A Qw/ST (Qwiic/STEMMA QT) port allows plug-and-play attachment of I2C sensors and breakouts via cable. An SP/CE connector provides a similar cable-based route for SPI or serial devices. A 3-pin JST-SH debug connector supports SWD debugging, while onboard reset and BOOT buttons add convenient control.

16MB QSPI flash with XiP decides capacity fit

The board provides 16MB of QSPI flash memory supporting execute-in-place operation alongside 8MB of PSRAM. This combination determines whether the available non-volatile storage and volatile workspace meet the firmware footprint and runtime buffer requirements of a given project.

Põhijooned

  • Dual Arm Cortex-M33 cores reach 150 MHz for responsive edge processing
  • 16 MB QSPI flash supports execute-in-place for large firmware images
  • 8 MB PSRAM expands runtime memory for data-heavy applications
  • USB-C provides power, programming and data through one cable
  • Qw/ST, SP/CE and debug connectors enable solderless add-ons and SWD access

Tehnilised andmed

Selle toote kohta ei ole veel tehnilisi andmeid avaldatud.

Küsimused selle toote kohta

Will the 16MB flash memory need replacement after repeated programming cycles?

The 16MB QSPI flash supports execute-in-place operation and is rated for typical microcontroller endurance; normal development use will not wear it out.

What limits sustained performance when the dual Cortex-M33 cores run at 150MHz continuously?

The 520KB of on-chip SRAM and thermal envelope of the RP2350B package are the first constraints under heavy continuous load.

How much heat and power does the board draw when powered via USB-C all day?

The RP2350B draws modest current at 150MHz, so the board stays cool and runs from a standard USB-C supply without extra cooling.

Veel samast osakonnast

Kliendid võrdlesid neid ka

Sama osakond, sama kassa — kaheksa krüptovaluutat ja 30-minutiline kursilukk.