Prihvaćamo kriptovalute — tako kriptovalute koje posjedujete mogu kupiti pravi hardver.Plaćajte kriptovalutom, trošite je na pravi hardver. Besplatna osigurana dostava diljem svijeta iznad 399 $. Obični vanjski kartoni bez oznaka, otpremaju se iz Njemačke.Besplatna osigurana dostava iznad 399 $. Vaš je tečaj blokiran 30 minuta od otvaranja blagajne.Tečaj blokiran 30 minuta. Svaki je artikl zapečaćen, njegov serijski broj provjeren, i pokriven jamstvom od 24 mjeseca.Zapečaćen, jamstvo 24 mjeseca.

Praćeni artikli Prijava
White 2.85 mm TPU filament spool, 500 g, semi-flexible

E3D Online

E3D Online spoolWorks FleXD Semi-flexible TPU Filament 2.85mm 500g Bright White02 3d printers accessory

SKU CH-10PX-04PFE

Semi-flexible TPU filament in 2.85 mm diameter on a 500 g spool, easy to print at 220–240 °C with 45–85 °C bed temperature and 30 % speed (15 mm/s)

  • ColorWhite
  • TypeFilament
  • Easy to print with 30 % print speed at 15 mm/s
  • High shear strength for durable functional parts
  • High abrasion resistance extends part lifespan
  • Elastic semi-flexible TPU prints bendable phone cases and insoles
  • Bright White colour stays vivid at 220–240 °C nozzle temp

E3D FleXD TPU Filament 2.85mm

E3D FleXD is a semi-flexible TPU filament supplied on a 500g spool in Bright White. The 2.85mm diameter suits printers that accept this format. It targets makers who need elastic, abrasion-resistant parts such as phone cases, insoles or protective covers.

Print temperature 220-240°C and bed 45-85°C

The material prints at 220-240°C nozzle temperature with a heated bed between 45-85°C. A print speed of 15mm/s, roughly 30% of typical rigid filament speeds, is recommended. Glue stick provides reliable bed adhesion. These settings give consistent layer bonding for functional flexible prints.

Low-speed printing reduces heat and noise

Running at 15mm/s keeps extruder load modest and limits hot-end dwell time, so cooling fans can run slower and quieter. The lower throughput also reduces instantaneous power draw compared with faster rigid filaments. Overall thermal load stays gentle on the printer during extended flexible jobs.

Istaknuto

  • Easy to print with 30 % print speed at 15 mm/s
  • High shear strength for durable functional parts
  • High abrasion resistance extends part lifespan
  • Elastic semi-flexible TPU prints bendable phone cases and insoles
  • Bright White colour stays vivid at 220–240 °C nozzle temp

Specifikacije

BrandE3D
ModelFleXD
ColorWhite
TypeFilament

Pitanja o ovom artiklu

Will this 2.85 mm FleXD filament feed reliably on a Bowden setup that usually runs rigid PLA?

Yes — the semi-flexible TPU formulation has high shear strength and prints at 15 mm/s, so it feeds through Bowden tubes without the buckling common with softer flexibles.

How can I confirm the first layer is adhering correctly at the 45-85 °C bed range?

Watch for a smooth, glossy first layer at 30 % speed; if edges lift, raise the bed toward 85 °C and apply a thin glue-stick layer as recommended.

Does the 500 g spool include a glue stick for bed adhesion or must I buy one separately?

The spool contains only the filament; a glue stick for bed adhesion is not included and must be purchased separately.

Također u ovoj kategoriji

Kupci su usporedili ovo

Ista polica, ista blagajna — osam valuta i blokada tečaja na 30 minuta.