Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
White 2.85 mm TPU filament spool, 500 g, semi-flexible

E3D Online

E3D Online spoolWorks FleXD Semi-flexible TPU Filament 2.85mm 500g Bright White02 3d printers accessory

SKU CH-10PX-04PFE

Semi-flexible TPU filament in 2.85 mm diameter on a 500 g spool, easy to print at 220–240 °C with 45–85 °C bed temperature and 30 % speed (15 mm/s)

  • ColorWhite
  • TypeFilament
  • Easy to print with 30 % print speed at 15 mm/s
  • High shear strength for durable functional parts
  • High abrasion resistance extends part lifespan
  • Elastic semi-flexible TPU prints bendable phone cases and insoles
  • Bright White colour stays vivid at 220–240 °C nozzle temp

E3D FleXD TPU Filament 2.85mm

E3D FleXD is a semi-flexible TPU filament supplied on a 500g spool in Bright White. The 2.85mm diameter suits printers that accept this format. It targets makers who need elastic, abrasion-resistant parts such as phone cases, insoles or protective covers.

Print temperature 220-240°C and bed 45-85°C

The material prints at 220-240°C nozzle temperature with a heated bed between 45-85°C. A print speed of 15mm/s, roughly 30% of typical rigid filament speeds, is recommended. Glue stick provides reliable bed adhesion. These settings give consistent layer bonding for functional flexible prints.

Low-speed printing reduces heat and noise

Running at 15mm/s keeps extruder load modest and limits hot-end dwell time, so cooling fans can run slower and quieter. The lower throughput also reduces instantaneous power draw compared with faster rigid filaments. Overall thermal load stays gentle on the printer during extended flexible jobs.

Přednosti

  • Easy to print with 30 % print speed at 15 mm/s
  • High shear strength for durable functional parts
  • High abrasion resistance extends part lifespan
  • Elastic semi-flexible TPU prints bendable phone cases and insoles
  • Bright White colour stays vivid at 220–240 °C nozzle temp

Specifikace

BrandE3D
ModelFleXD
ColorWhite
TypeFilament

Otázky k tomuto produktu

Will this 2.85 mm FleXD filament feed reliably on a Bowden setup that usually runs rigid PLA?

Yes — the semi-flexible TPU formulation has high shear strength and prints at 15 mm/s, so it feeds through Bowden tubes without the buckling common with softer flexibles.

How can I confirm the first layer is adhering correctly at the 45-85 °C bed range?

Watch for a smooth, glossy first layer at 30 % speed; if edges lift, raise the bed toward 85 °C and apply a thin glue-stick layer as recommended.

Does the 500 g spool include a glue stick for bed adhesion or must I buy one separately?

The spool contains only the filament; a glue stick for bed adhesion is not included and must be purchased separately.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.