Prihvaćamo kriptovalute — tako kriptovalute koje posjedujete mogu kupiti pravi hardver.Plaćajte kriptovalutom, trošite je na pravi hardver. Besplatna osigurana dostava diljem svijeta iznad 399 $. Obični vanjski kartoni bez oznaka, otpremaju se iz Njemačke.Besplatna osigurana dostava iznad 399 $. Vaš je tečaj blokiran 30 minuta od otvaranja blagajne.Tečaj blokiran 30 minuta. Svaki je artikl zapečaćen, njegov serijski broj provjeren, i pokriven jamstvom od 24 mjeseca.Zapečaćen, jamstvo 24 mjeseca.

Praćeni artikli Prijava
Pink aluminium-alloy enclosed switch-mode power supply unit

myVolts

myVolts Switch Power Supply S-720-12 12V 60A 720W pink

SKU CH-D9RM-VPSNC

A 720 W AT switch-mode unit delivers 12 V at 60 A with overload, over-voltage and short-circuit protection, CCC, FCC and CE compliance, and an aluminium-alloy chassis rated for 0–40 °C operation

  • TypeAT
  • High efficiency with low DC ripple for stable output
  • Operates from 0 °C to 40 °C with long service life
  • High insulation strength for safe industrial use
  • 100 % full-load burn-in test completed before shipment
  • circuit, overload and overvoltage protection built in

Industrial 12V 720W power supply

This switching power supply delivers 12 V DC at up to 60 A for a total of 720 W. It is built for industrial automation, CCTV, LED displays and 3D printers that need a stable DC source. The unit accepts AC input from 170 to 250 V and carries CCC, FCC and CE compliance marks. It suits engineers and technicians who require a fixed-voltage rail for heavy continuous loads.

Sustained-load behaviour

The supply is rated for continuous operation at 100 % load after a full-load burn-in test. Overload, overvoltage and short-circuit protection circuits guard the output during prolonged use. High insulation strength and low DC ripple maintain clean power under steady demand. Operating temperature range is 0 to 40 °C, so enclosure airflow must keep ambient air within that band.

Pre-installation checks

Verify that your mains supply stays between 170 and 250 V AC before connecting the L and N terminals. Confirm the load does not exceed 60 A at 12 V and that wiring gauge can handle the current safely. Ensure the mounting location stays within the 0 to 40 °C operating window and 0 to 95 % non-condensing humidity. Check that the adjustable voltage trim is set correctly for the connected equipment.

Istaknuto

  • High efficiency with low DC ripple for stable output
  • Operates from 0 °C to 40 °C with long service life
  • High insulation strength for safe industrial use
  • 100 % full-load burn-in test completed before shipment
  • circuit, overload and overvoltage protection built in

Specifikacije

TypeAT

Pitanja o ovom artiklu

How much heat and noise does the 720W unit produce when running continuously?

It uses natural convection cooling with no fan, so it runs silently; the aluminium alloy case dissipates heat within the rated 0~40 °C working temperature range.

What cables or connectors must I already have to wire this supply?

You need mains leads for the L and N terminals and suitable DC cables for the V+ and GND screw terminals; no plug-and-play cables are included.

Will the 12 V 60 A output work safely with older 12 V gear that draws less current?

Yes, the unit delivers up to 60 A but only supplies what the load draws, and built-in short-circuit, overload and overvoltage protection guards legacy devices.

Također u ovoj kategoriji

Kupci su usporedili ovo

Ista polica, ista blagajna — osam valuta i blokada tečaja na 30 minuta.