Akceptujemy kryptowaluty — posiadane środki można więc wykorzystać na zakup prawdziwego sprzętu.Płatność kryptowalutą — realny sprzęt w zamian. Bezpłatna, ubezpieczona dostawa na całym świecie powyżej 399 $. Neutralne kartony, bez oznaczeń, wysyłane z Niemiec.Bezpłatna, ubezpieczona dostawa powyżej 399 $. Kurs zostaje zablokowany na 30 minut od otwarcia kasy.Kurs zablokowany na 30 minut. Każdy produkt jest fabrycznie zapieczętowany, jego numer seryjny jest sprawdzany, a całość objęta jest 24-miesięczną gwarancją.Zapieczętowane fabrycznie, 24 miesiące gwarancji.

Obserwowane produkty Zaloguj się
Pink aluminium-alloy enclosed switch-mode power supply unit

myVolts

myVolts Switch Power Supply S-720-12 12V 60A 720W pink

SKU CH-D9RM-VPSNC

A 720 W AT switch-mode unit delivers 12 V at 60 A with overload, over-voltage and short-circuit protection, CCC, FCC and CE compliance, and an aluminium-alloy chassis rated for 0–40 °C operation

  • TypeAT
  • High efficiency with low DC ripple for stable output
  • Operates from 0 °C to 40 °C with long service life
  • High insulation strength for safe industrial use
  • 100 % full-load burn-in test completed before shipment
  • circuit, overload and overvoltage protection built in

Industrial 12V 720W power supply

This switching power supply delivers 12 V DC at up to 60 A for a total of 720 W. It is built for industrial automation, CCTV, LED displays and 3D printers that need a stable DC source. The unit accepts AC input from 170 to 250 V and carries CCC, FCC and CE compliance marks. It suits engineers and technicians who require a fixed-voltage rail for heavy continuous loads.

Sustained-load behaviour

The supply is rated for continuous operation at 100 % load after a full-load burn-in test. Overload, overvoltage and short-circuit protection circuits guard the output during prolonged use. High insulation strength and low DC ripple maintain clean power under steady demand. Operating temperature range is 0 to 40 °C, so enclosure airflow must keep ambient air within that band.

Pre-installation checks

Verify that your mains supply stays between 170 and 250 V AC before connecting the L and N terminals. Confirm the load does not exceed 60 A at 12 V and that wiring gauge can handle the current safely. Ensure the mounting location stays within the 0 to 40 °C operating window and 0 to 95 % non-condensing humidity. Check that the adjustable voltage trim is set correctly for the connected equipment.

Najważniejsze cechy

  • High efficiency with low DC ripple for stable output
  • Operates from 0 °C to 40 °C with long service life
  • High insulation strength for safe industrial use
  • 100 % full-load burn-in test completed before shipment
  • circuit, overload and overvoltage protection built in

Specyfikacja

TypeAT

Pytania dotyczące tego produktu

How much heat and noise does the 720W unit produce when running continuously?

It uses natural convection cooling with no fan, so it runs silently; the aluminium alloy case dissipates heat within the rated 0~40 °C working temperature range.

What cables or connectors must I already have to wire this supply?

You need mains leads for the L and N terminals and suitable DC cables for the V+ and GND screw terminals; no plug-and-play cables are included.

Will the 12 V 60 A output work safely with older 12 V gear that draws less current?

Yes, the unit delivers up to 60 A but only supplies what the load draws, and built-in short-circuit, overload and overvoltage protection guards legacy devices.

Także w tym dziale

Klienci porównywali też te produkty

Ten sam dział, ta sama kasa — osiem kryptowalut i 30-minutowa blokada kursu.