Elfogadjuk a kriptovalutát — így az Ön birtokában lévő érmékből valódi hardvert vásárolhat.Fizessen kriptóval, és költse el valódi hardverre. 399 $ felett világszerte díjmentes a biztosított szállítás. Egyszerű, jelöletlen külső kartonok, Németországból küldve.399 $ felett díjmentes a biztosított szállítás. Az Ön árfolyama a pénztár megnyitásától számított 30 percre zárolva marad.Árfolyam zárolva 30 percre. Minden termék gyárilag zárt, sorozatszáma ellenőrzött, és 24 hónapos garancia fedezi.Zárt csomagolás, 24 hónap garancia.

Árfigyelő lista Bejelentkezés
Silver 3.5 inch hard drive with green circuit board and mounted tray

HPE

HPE MB4000GVYZK 4TB SATA 6.0Gb/s 7200 RPM 3.5" internal hard drive

SKU CH-Y4TH-RB9QB

A 4 TB SATA 6.0 Gb/s 7200 RPM 3.5" internal hard drive with digitally signed firmware and included tray

  • InterfaceSATA 6.0Gb/s
  • Capacity4TB
  • RPM7200 RPM
  • Form Factor3.5"
  • 4 TB capacity stores large data sets
  • 7200 RPM spindle delivers responsive throughput
  • SATA 6.0 Gb/s interface enables fast transfers
  • 5 inch form factor fits standard drive bays
  • Digitally signed firmware protects drive integrity

4 TB SATA hard drive

The HPE MB4000GVYZK is a 4TB 3.5 inch internal hard drive built for desktop systems. It spins at 7200 RPM and connects through a SATA 6.0Gb/s interface. Digitally signed firmware helps protect data integrity during operation. The drive ships with a tray for standard large-form-factor bays.

Suited for bulk storage, not speed

This drive suits users who need affordable terabytes for backups, media libraries or archival workloads. The 7.2K spindle speed delivers steady sequential throughput for large files. Buyers who want low latency for operating systems or databases should look at solid-state alternatives. Systems limited to SATA 3.0Gb/s will not reach the interface ceiling.

SATA 6.0Gb/s interface decides fit

The single specification that decides compatibility is the SATA 6.0Gb/s interface. Your motherboard or controller must support this link speed to obtain the rated transfer rate. A 3.5 inch drive bay and a standard SATA power connector are also required. Verify both before purchase.

Erősségek

  • 4 TB capacity stores large data sets
  • 7200 RPM spindle delivers responsive throughput
  • SATA 6.0 Gb/s interface enables fast transfers
  • 5 inch form factor fits standard drive bays
  • Digitally signed firmware protects drive integrity

Műszaki adatok

BrandHPE
ModelMB4000GVYZK
InterfaceSATA 6.0Gb/s
Capacity4TB
RPM7200 RPM
Form Factor3.5"

Kérdések a termékről

Do I need a SATA 6.0 Gb/s port and a 3.5-inch drive bay with an SC tray slot to install this 4 TB HPE drive?

Yes — the drive connects over a SATA 6.0 Gb/s interface and fits a standard 3.5-inch bay using the supplied SC tray, so both the port and the bay must match.

Will this 7200 RPM SATA drive share a controller with an older SATA 3.0 Gb/s drive without slowing the new drive?

The controller will negotiate each link independently; the older drive runs at 3.0 Gb/s while this drive operates at its rated 6.0 Gb/s.

How can I confirm the digitally signed firmware is active after installation?

Check the drive’s firmware revision in the system BIOS or HPE management software — it should match the signed version listed on the HPE support page for part MB4000GVYZK.

Szintén ezen a polcon

Vásárlók ezeket hasonlították össze

Ugyanaz a polc, ugyanaz a pénztár — nyolc pénznem és 30 perces árfolyamzár.