Sprejemamo kriptovalute — tako lahko sredstva, ki jih imate, kupijo pravo strojno opremo.Plačajte v kriptovaluti, zapravite jo za pravo strojno opremo. Brezplačna zavarovana dostava po vsem svetu nad 399 $. Nevtralni kartoni brez znamke, poslani iz Nemčije.Brezplačna zavarovana dostava nad 399 $. Vaš tečaj je zaklenjen za 30 minut, takoj ko se odpre blagajna.Tečaj zaklenjen 30 minut. Vsak izdelek je zapečaten, njegova serijska številka preverjena, in krit z 24-mesečno garancijo.Zapečateno, 24-mesečna garancija.

Spremljani izdelki Prijava
Silver 3.5 inch hard drive with green circuit board and mounted tray

HPE

HPE MB4000GVYZK 4TB SATA 6.0Gb/s 7200 RPM 3.5" internal hard drive

SKU CH-Y4TH-RB9QB

A 4 TB SATA 6.0 Gb/s 7200 RPM 3.5" internal hard drive with digitally signed firmware and included tray

  • InterfaceSATA 6.0Gb/s
  • Capacity4TB
  • RPM7200 RPM
  • Form Factor3.5"
  • 4 TB capacity stores large data sets
  • 7200 RPM spindle delivers responsive throughput
  • SATA 6.0 Gb/s interface enables fast transfers
  • 5 inch form factor fits standard drive bays
  • Digitally signed firmware protects drive integrity

4 TB SATA hard drive

The HPE MB4000GVYZK is a 4TB 3.5 inch internal hard drive built for desktop systems. It spins at 7200 RPM and connects through a SATA 6.0Gb/s interface. Digitally signed firmware helps protect data integrity during operation. The drive ships with a tray for standard large-form-factor bays.

Suited for bulk storage, not speed

This drive suits users who need affordable terabytes for backups, media libraries or archival workloads. The 7.2K spindle speed delivers steady sequential throughput for large files. Buyers who want low latency for operating systems or databases should look at solid-state alternatives. Systems limited to SATA 3.0Gb/s will not reach the interface ceiling.

SATA 6.0Gb/s interface decides fit

The single specification that decides compatibility is the SATA 6.0Gb/s interface. Your motherboard or controller must support this link speed to obtain the rated transfer rate. A 3.5 inch drive bay and a standard SATA power connector are also required. Verify both before purchase.

Poudarki

  • 4 TB capacity stores large data sets
  • 7200 RPM spindle delivers responsive throughput
  • SATA 6.0 Gb/s interface enables fast transfers
  • 5 inch form factor fits standard drive bays
  • Digitally signed firmware protects drive integrity

Specifikacije

BrandHPE
ModelMB4000GVYZK
InterfaceSATA 6.0Gb/s
Capacity4TB
RPM7200 RPM
Form Factor3.5"

Vprašanja o tem izdelku

Do I need a SATA 6.0 Gb/s port and a 3.5-inch drive bay with an SC tray slot to install this 4 TB HPE drive?

Yes — the drive connects over a SATA 6.0 Gb/s interface and fits a standard 3.5-inch bay using the supplied SC tray, so both the port and the bay must match.

Will this 7200 RPM SATA drive share a controller with an older SATA 3.0 Gb/s drive without slowing the new drive?

The controller will negotiate each link independently; the older drive runs at 3.0 Gb/s while this drive operates at its rated 6.0 Gb/s.

How can I confirm the digitally signed firmware is active after installation?

Check the drive’s firmware revision in the system BIOS or HPE management software — it should match the signed version listed on the HPE support page for part MB4000GVYZK.

Tudi v tem oddelku

Stranke so primerjale tudi te

Ista polica, ista blagajna — osem kriptovalut in 30-minutni zaklep tečaja.