BFKK 3U Rackmount Server Chassis EATX/ATX/MATX 4x5.25 6x3.5 Top/Side Cooling
- Rackmount
Elfogadjuk a kriptovalutát — így az Ön birtokában lévő érmékből valódi hardvert vásárolhat.Fizessen kriptóval, és költse el valódi hardverre. 399 $ felett világszerte díjmentes a biztosított szállítás. Egyszerű, jelöletlen külső kartonok, Németországból küldve.399 $ felett díjmentes a biztosított szállítás. Az Ön árfolyama a pénztár megnyitásától számított 30 percre zárolva marad.Árfolyam zárolva 30 percre. Minden termék gyárilag zárt, sorozatszáma ellenőrzött, és 24 hónapos garancia fedezi.Zárt csomagolás, 24 hónap garancia.
RIMLANCE
A 16GB dual-channel DDR4 kit running at 2666MHz with CL19 latency and 1.2V operation for standard desktop upgrades
This RIMLANCE kit provides 16GB of memory as two 8GB UDIMM modules built for DDR4 platforms. It targets users who want a straightforward capacity increase for everyday multitasking and office workloads. The unbuffered, non-ECC design matches standard consumer motherboard requirements. Installation follows the usual 288-pin DIMM procedure without extra configuration steps.
Operating at the standard 1.2V DDR4 voltage, the modules draw minimal power and produce little heat during typical desktop use. No active cooling is required and the sticks run silently inside the case. The low voltage also helps keep overall system power draw modest under normal multitasking loads. Stable operation is maintained at the rated 2666MHz speed with CL19 latency.
This kit upgrades systems running slower DDR4 speeds or smaller capacities such as single 8GB modules. The jump is worthwhile when the motherboard supports 2666MHz and the user needs more headroom for browser tabs, office suites or light content creation. It does not suit builds that require ECC, registered DIMMs or speeds beyond the PC4-21300 rating.
| Brand | RIMLANCE |
|---|---|
| Model | RUD21300S6C2K16 |
| Capacity | 16GB (2 x 8GB) |
| Type | 288-Pin PC RAM |
| Speed | DDR4 2666 (PC4 21300) |
| CAS Latency | CL19 |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major Brand Chipset |
Align the notch on each 288-pin module with the slot key, press straight down until both retention clips click, and ensure the motherboard is powered off; the common mistake is seating only one side so the clip on the other side stays open.
No scheduled maintenance is required; keep the gold contacts clean and ensure case airflow stays adequate. If a module fails, replace the faulty 8GB stick with another DDR4 2666 CL19 1.2V UDIMM of matching capacity.
The CAS latency of CL19 at 1.2V sets the timing floor; under continuous heavy throughput the fixed latency and voltage become the bottleneck before thermal limits on standard unbuffered DDR4 modules.
Szintén ezen a polcon
Ugyanaz a polc, ugyanaz a pénztár — nyolc pénznem és 30 perces árfolyamzár.
Amivel fizet, és amiben az árakat olvassa.
A pénztárnál küldi el a tárcájából
Csak tájékoztató jellegű — a katalógus dollárban van árazva
Nincs ilyen pénznem.
Válassza ki, milyen nyelven szóljon Önhöz az oldal.
Nincs egyező nyelv.
Először jár itt?
Már van fiókja?
Nincs automatikus visszaállítás: ez a bolt nem küld e-mailt, tehát nincs kérhető egyszer használatos link. Hagyja meg a fiókhoz tartozó címet, azt valaki kézzel átnézi.
Kérés rögzítve
Semmi nem érkezik a postafiókjába — ez a bolt egyáltalán nem küld e-mailt. Ezeket valaki kézzel intézi.
Eszébe jutott?