Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Thin black cable with SlimSAS and OCuLink connectors, .5m length

LORDWORLD

LORDWORLD MB402L-B SlimSAS 4i SFF-8654 to OCuLink 4i SFF-8611 Cable .5m

SKU CH-40BC-18XNG

A .5 m cable linking SlimSAS 8654 to OCuLink 8611 with locking latches, rated for PCIe 4.0 and SFF-9402 compliant

  • 5 m length keeps signal paths short for PCIe 4.0 speeds
  • SlimSAS SFF-8654 to OCuLink SFF-8611 connectors match spec exactly
  • Locking latch on both ends prevents accidental disconnects
  • SFF-9402 compliant design works with mainstream NVMe HBA and RAID cards
  • UL 20744 certified cable meets safety requirements

SlimSAS 4i SFF-8654 to OCuLink 4i SFF-8611 Cable

This .5 metre cable connects a SlimSAS 4i SFF-8654 interface to an OCuLink 4i SFF-8611 interface. It is built to SFF-9402 compliant design specifications and supports PCIe 4.0 transfer speeds. Locking latches on both connectors provide a secure connection. The cable carries UL20744 certification for safety compliance.

Suits builders linking NVMe

This cable suits builders who need a short, certified link between compatible controller cards and backplanes or devices using the matching port types. It is not for installations requiring a longer run than .5 metres. It is also not for systems that lack either a SlimSAS 4i SFF-8654 or an OCuLink 4i SFF-8611 port.

PCIe 4.0 transfer speed over SFF-9402 compliant

The specification that decides fit is the PCIe 4.0 transfer speed supported over an SFF-9402 compliant cable assembly. Your controller and target device must both operate at this interface generation to realise the rated performance. Verify that your hardware explicitly lists compatibility with this cable standard before purchasing.

Helstu kostir

  • 5 m length keeps signal paths short for PCIe 4.0 speeds
  • SlimSAS SFF-8654 to OCuLink SFF-8611 connectors match spec exactly
  • Locking latch on both ends prevents accidental disconnects
  • SFF-9402 compliant design works with mainstream NVMe HBA and RAID cards
  • UL 20744 certified cable meets safety requirements

Tæknilýsing

BrandLORDWORLD

Spurningar um þessa vöru

Which controller card slot does the SFF-8654 end of this cable plug into?

The SFF-8654 connector fits a SlimSAS 4i port on an NVMe or Tri-mode HBA/RAID card that follows the SFF-9402 pinout.

Will the 0.5 m length reach from a rear-mounted HBA to a front-panel OCuLink backplane in a standard 4U chassis?

At 19.69 inches the cable spans typical 4U depths; the locking latches on both SFF-8654 and SFF-8611 ends keep the link secure under vibration.

How can I verify the link is running at PCIe 4.0 speeds after installation?

Check the controller BIOS or OS tool (lspci -vv / nvme list) for a x4 Gen 4.0 negotiation and confirm zero CRC errors on the attached NVMe drives.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.