Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
LORDWORLD MCIO 8i to dual OCuLink 4i cable, .5 m, locking latches

LORDWORLD

LORDWORLD MCIO 8i SFF-TA-1016 to 2x OCuLink 4i SFF-8611 Cable 0.5m

SKU CH-3XS3-FABB8

Connects an MCIO 8i SFF-TA-1016 port to two OCuLink 4i SFF-8611 devices with a 0.5 m cable supporting PCIe 4.0 speeds and locking latches

  • 5 m length fits tight server builds
  • PCIe 4.0 transfer speeds meet SFF-TA-1016 and SFF-8611 specs
  • Locking OCuLink latches keep cables secure under vibration
  • SFF-9402 compliant design works with mainstream NVMe HBA and RAID cards
  • Single MCIO 8i splits to two OCuLink 4i ports

MCIO 8i to Dual OCuLink Adapter

This LORDWORLD adapter cable converts a single MCIO 8i SFF-TA-1016 port into two OCuLink 4i SFF-8611 connections. It enables direct attachment of NVMe storage devices to compatible tri-mode HBA or RAID controllers. The 0.5 metre length suits internal routing within server or workstation chassis. Builders expanding high-speed storage arrays will find this cable matches the required interface.

SFF-9402 Compliant Build with Locking Latches

Connectors follow SFF-TA-1016 and SFF-8611 design specifications for reliable mating. The OCuLink ends feature locking latches that resist accidental disconnection during vibration or maintenance. Cable construction meets SFF-9402 requirements, supporting signal integrity for PCIe 4.0 transfer speeds. The fixed 19.69 inch length reduces excess slack that can impede airflow in dense enclosures.

Enables Dual NVMe Links from One Controller Port

Splitting one MCIO 8i interface into two OCuLink 4i paths lets a single controller port drive two separate NVMe devices. This topology simplifies cabling for dual-drive configurations without consuming additional controller slots. The adapter ships as a standalone cable; no driver installation or configuration software is required. Systems lacking an MCIO 8i source port cannot use this cable.

Helstu kostir

  • 5 m length fits tight server builds
  • PCIe 4.0 transfer speeds meet SFF-TA-1016 and SFF-8611 specs
  • Locking OCuLink latches keep cables secure under vibration
  • SFF-9402 compliant design works with mainstream NVMe HBA and RAID cards
  • Single MCIO 8i splits to two OCuLink 4i ports

Tæknilýsing

BrandLORDWORLD

Spurningar um þessa vöru

What PCIe generation does the MCIO 8i to dual OCuLink cable support?

The cable meets PCIe 4.0 specifications for transfer speeds across both OCuLink 4i connections.

What clearance is needed for the MCIO 8i SFF-TA-1016 connector?

The MCIO 8i plug follows the SFF-TA-1016 form factor and requires a standard MCIO 8i port on the host card or backplane.

How do you secure the OCuLink ends so they do not disconnect under vibration?

Each OCuLink 4i connector has a locking latch; press the connector fully into the port until the latch clicks into place.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.