Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Compact black ABS case with four USB-A ports and pogo pins for Raspberry Pi Zero

LORDWORLD

LORDWORLD USB Hub HAT (B) for Raspberry Pi Zero — 4× USB 2.0/1.1

SKU CH-JAP6-R5GKR

Adds four USB 2.0 ports to Raspberry Pi Zero boards via pogo pins in a snap-fit ABS case

  • Add four USB ports to a Raspberry Pi Zero with a pogo-pin HAT
  • Direct GPIO connection via spring-loaded pins for Zero, Zero W and Zero WH
  • Four ports support USB 2.0 and 1.1 peripherals
  • Snap-on lid with rounded edges for tool-free enclosure
  • ABS shell with dull-polish finish resists fingerprints

Designed for Raspberry Pi Zero

The LORDWORLD USB Hub HAT (B) adds four USB 2.0/1.1 ports to any Raspberry Pi Zero series board. It connects through pogo pins that press directly against the Zero, Zero W or Zero WH without soldering. The enclosure uses rounded ABS plastic with a dull-polish, anti-fingerprint finish and a simple snap-on lid.

Upgrading from the single USB OTG port

The stock Zero boards expose only one micro-USB OTG connection, which limits peripheral count. This HAT replaces that single link with four full-size Type-A sockets, so a keyboard, mouse, storage and a network dongle can run together. The jump is worth it when a project needs simultaneous USB devices and the Pi must stay inside a compact case.

Check your Zero model and power budget

Verify you have a Zero, Zero W or Zero WH; the pogo pin layout matches only those boards. Ensure your power supply can deliver enough current for the Pi plus every attached USB device, because the HAT draws bus power from the Pi itself. No driver installation is required on standard Raspberry Pi OS images.

Helstu kostir

  • Add four USB ports to a Raspberry Pi Zero with a pogo-pin HAT
  • Direct GPIO connection via spring-loaded pins for Zero, Zero W and Zero WH
  • Four ports support USB 2.0 and 1.1 peripherals
  • Snap-on lid with rounded edges for tool-free enclosure
  • ABS shell with dull-polish finish resists fingerprints

Tæknilýsing

BrandLORDWORLD

Spurningar um þessa vöru

Does the case lid snap on without screws?

The lid uses a simple snap design with rounded angles and no screws are required to close the ABS enclosure.

How does the HAT connect to the Raspberry Pi Zero without a header?

Pogo pins on the underside mate directly with the Zero board pads so no soldered GPIO header is needed.

Will the four USB ports still work if I later upgrade to a newer Zero board?

The hub is compatible with the Zero series including Zero W and Zero WH, so it will continue to provide four USB 2.0/1.1 ports on those models.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.