Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Green circuit board with 40-pin header and terminal blocks, status LEDs along the edge

MCDODO

MCDODO Freenove Breakout Board Raspberry Pi Terminal Block Shield HAT 40-pin GPIO Status LED 2.54mm

SKU CH-ATWY-ETQBQ

Connects to Raspberry Pi 40-pin header via terminal blocks and headers with 2.54mm pitch and status LEDs

  • TypeSingle Board Computers
  • Compatible with Raspberry Pi 5 through Zero models
  • 40-pin GPIO header with 2.54 mm pitch terminal blocks
  • On-board status LEDs show high or low logic levels
  • LEDs driven by dedicated chip leaving GPIO unaffected
  • BCM pin names printed beside each connection point

Raspberry Pi GPIO Breakout HAT

The Freenove Breakout Board is a terminal block shield HAT that fits the 40-pin GPIO header on Raspberry Pi models from the Zero series through the Pi 5. It adds screw terminals and a pin header so you can connect wires without soldering. Each GPIO pin is labelled with its BCM number beside the terminal. Status LEDs show high or low logic levels without loading the GPIO pins themselves. The board suits makers and engineers who need quick, removable wiring for sensors, relays or other peripherals.

2.54 mm pitch terminal block limits

All terminals use a 2.54 mm pitch, which matches the standard Raspberry Pi header spacing. This spacing limits wire gauge to sizes that fit the terminal openings and makes the board wider than the Pi Zero footprint. The shield is not compatible with the Raspberry Pi 400 or 500 because those models do not expose a standard 40-pin header in the same layout. Builders who need denser connections or a lower profile for tight enclosures should consider alternative wiring methods.

Upgrading from jumper wires or breadboards

This HAT replaces loose jumper wires and breadboard setups that can vibrate loose or misconnect during development. The screw terminals give a secure, repeatable connection for field deployment or long-term test rigs. The jump is worth it when you move from prototyping to a permanent install, or when you frequently swap sensors and need clear BCM labels to avoid wiring errors. It does not add extra GPIO pins or change the electrical characteristics of the Pi header.

Helstu kostir

  • Compatible with Raspberry Pi 5 through Zero models
  • 40-pin GPIO header with 2.54 mm pitch terminal blocks
  • On-board status LEDs show high or low logic levels
  • LEDs driven by dedicated chip leaving GPIO unaffected
  • BCM pin names printed beside each connection point

Tæknilýsing

TypeSingle Board Computers

Spurningar um þessa vöru

Which Raspberry Pi models does this breakout board support?

It fits Raspberry Pi 5, 4B, 3B+, 3B, 3A+, 2B, 1B+, 1A+, Zero 2 W, Zero W and Zero; it does not fit the 400 or 500 models.

What does the GPIO status LED show when a pin is driven high?

The LED lights when the GPIO outputs or reads a high level and stays off for a low level; the indicator is driven by an onboard chip so the GPIO line itself is not loaded.

What is the pin pitch of the terminal block and header?

Both the terminal block and the 40-pin header use a 2.54 mm pitch.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.