Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Rectangular stainless steel switching power supply, 21.5 by 11.5 by 5 cm, natural cooling, AC input selector switch visible

myVolts

myVolts Fesjoy 24V 15A 360W Switching Power Supply for Ender-3 LED Strip Computer Project Home Appliance

SKU CH-4Q5V-98HBB

Converts AC 110V or 240V to DC 24V at 15A and 360W with overload, over-voltage and short-circuit protection for 3D printers, LED strips and home appliances

  • TypeAT
  • Converts AC 110V or 220V to stable DC 24V 15A 360W output
  • Selectable input voltage switch matches local mains before powering on
  • Over-voltage, overload, over-temperature and short-circuit protections guard connected equipment
  • Operates from -20°C to 60°C with fan-less natural cooling
  • Compact 21.5 × 11.5 × 5 cm stainless-steel case fits tight project enclosures

24V 15A Switching Supply for 3D Printers

This myVolts Fesjoy unit converts AC 110V or 220V mains to a regulated DC 24V output rated at 15 amps and 360 watts. It is built around a pulse-width-modulation full-bridge topology and uses natural convection cooling inside a stainless-steel enclosure. The supply targets Ender-3 printers, LED strip installations and similar fixed-voltage projects.

Verify Mains Selector and Load Before Wiring

A sliding switch on the chassis selects between 110V and 220V AC input; it must match the local supply before power is applied. The adjustable output trims within ±10% of 24V, so confirm the connected device tolerates that range. Protection triggers at 105% to 150% of rated power for both over-voltage and overload, and the operating envelope spans -20°C to 60°C without frost.

Suits Fixed 24V Loads Up to 360W

Makers running an Ender-3, LED arrays or comparable 24V equipment within the 15A limit will find the steady output and passive cooling a good fit. Builds that need variable voltage, higher current, forced-air cooling or a different form factor should look elsewhere.

Helstu kostir

  • Converts AC 110V or 220V to stable DC 24V 15A 360W output
  • Selectable input voltage switch matches local mains before powering on
  • Over-voltage, overload, over-temperature and short-circuit protections guard connected equipment
  • Operates from -20°C to 60°C with fan-less natural cooling
  • Compact 21.5 × 11.5 × 5 cm stainless-steel case fits tight project enclosures

Tæknilýsing

TypeAT

Spurningar um þessa vöru

What comes in the package and do I need to buy a power cord separately?

The box contains the power supply unit only. A mains cable is not included and must be sourced separately.

Which input voltage setting should I select for UK mains?

Set the switch to the 240 V position before connecting to UK mains.

What does the 360 W rating mean for a 24 V Ender-3 build?

It delivers up to 15 A at 24 V, enough for the hot-end, heated bed and typical accessories on an Ender-3.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.