Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn

NEMIX RAM

NEMIX RAM 16GB DDR5 5600 CL46 1Rx8 ECC Registered RDIMM 288-pin 1.1V memory upgrade

SKU CH-TD4Y-2VRBN

16 GB DDR5-5600 registered ECC RDIMM, CL46 at 1.1 V, built for Supermicro H14SSL-NT servers

  • Capacity16GB
  • Type288-Pin DDR5 RDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCYes
  • Exact-match 16 GB DDR5-5600 CL46 1Rx8 RDIMM for full rated speed
  • Verified fit for Supermicro H14SSL-NT with 288-pin registered form factor
  • Registered architecture plus ECC prevents silent data corruption under full load
  • Major OEM Samsung Micron Hynix chips deliver enterprise-grade reliability
  • Lifetime replacement warranty with US-based technical support included

Exact-match DDR5 server upgrade

This 16 GB DDR5 5600 registered ECC RDIMM is built for the Supermicro H14SSL-NT motherboard. It runs at PC5-44800 with CL46 latency at 1.10 V. The 1Rx8 organisation and 288-pin form factor match the board's memory controller requirements precisely.

Suited for single-slot capacity adds

Buyers expanding a validated Supermicro H14SSL-NT configuration with one registered ECC module will benefit. Builders needing unbuffered UDIMMs, SODIMMs, non-ECC memory, or a different DDR generation should look elsewhere because the board will not accept them.

Straightforward slot installation

Align the key notch on the 288-pin edge connector with the motherboard slot and press until the retention clips latch. The registered design allows full-slot populations, but the manual must be followed for population order; skipping that step is the most common cause of a module not being recognised.

Helstu kostir

  • Exact-match 16 GB DDR5-5600 CL46 1Rx8 RDIMM for full rated speed
  • Verified fit for Supermicro H14SSL-NT with 288-pin registered form factor
  • Registered architecture plus ECC prevents silent data corruption under full load
  • Major OEM Samsung Micron Hynix chips deliver enterprise-grade reliability
  • Lifetime replacement warranty with US-based technical support included

Tæknilýsing

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Server Memory
ModelDDR5 ECC RDIMM Registered Server Memory
Part NumberMR44800-618K1
Capacity16GB
Type288-Pin DDR5 RDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCYes
Buffered/RegisteredRegistered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 ECC RDIMM Motherboard Compatible
Package Content16GB DDR5 5600MHz PC5-44800 1Rx8 1.1V 288-PIN ECC RDIMM KIT

Aðrar útgáfur af þessari vöru

5 í viðbót í sama vöruflokki

Sama fjölskylda, mismunandi minni, kælingu eða klukkuhraða — berðu saman áður en þú ákveður þig.

Spurningar um þessa vöru

What motherboard slot type is required for the 288-pin RDIMM to install?

The module needs a DDR5 288-pin RDIMM slot on a server motherboard that supports registered ECC memory and 1.1 V operation.

Will the CL46 timing work alongside existing DDR5 5600 RDIMMs in the same server?

Yes, matching the DDR5 5600 speed and CL46 latency lets the memory controller run all populated slots at the rated frequency.

How can I confirm the 1Rx8 registered ECC module is detected at full capacity after installation?

Check the BIOS memory map or the OS memory report — both should show the full 16 GB per DIMM with ECC active.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.