We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green bare circuit board DDR5 RDIMM memory module with black chips no heat spreader 288 pins

NEMIX RAM

NEMIX RAM 16GB DDR5 5600 CL46 1Rx8 ECC Registered RDIMM 288-pin 1.1V memory upgrade

SKU CH-TD4Y-2VRBN

16 GB DDR5-5600 registered ECC RDIMM, CL46 at 1.1 V, built for Supermicro H14SSL-NT servers

  • Capacity16GB
  • Type288-Pin DDR5 RDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCYes

Size 16GB

Show 24 more configurations
  • Exact-match 16 GB DDR5-5600 CL46 1Rx8 RDIMM for full rated speed
  • Verified fit for Supermicro H14SSL-NT with 288-pin registered form factor
  • Registered architecture plus ECC prevents silent data corruption under full load
  • Major OEM Samsung Micron Hynix chips deliver enterprise-grade reliability
  • Lifetime replacement warranty with US-based technical support included

Exact-match DDR5 server upgrade

This 16 GB DDR5 5600 registered ECC RDIMM is built for the Supermicro H14SSL-NT motherboard. It runs at PC5-44800 with CL46 latency at 1.10 V. The 1Rx8 organisation and 288-pin form factor match the board's memory controller requirements precisely.

Suited for single-slot capacity adds

Buyers expanding a validated Supermicro H14SSL-NT configuration with one registered ECC module will benefit. Builders needing unbuffered UDIMMs, SODIMMs, non-ECC memory, or a different DDR generation should look elsewhere because the board will not accept them.

Straightforward slot installation

Align the key notch on the 288-pin edge connector with the motherboard slot and press until the retention clips latch. The registered design allows full-slot populations, but the manual must be followed for population order; skipping that step is the most common cause of a module not being recognised.

Highlights

  • Exact-match 16 GB DDR5-5600 CL46 1Rx8 RDIMM for full rated speed
  • Verified fit for Supermicro H14SSL-NT with 288-pin registered form factor
  • Registered architecture plus ECC prevents silent data corruption under full load
  • Major OEM Samsung Micron Hynix chips deliver enterprise-grade reliability
  • Lifetime replacement warranty with US-based technical support included

Specifications

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Server Memory
ModelDDR5 ECC RDIMM Registered Server Memory
Part NumberMR44800-618K1
Capacity16GB
Type288-Pin DDR5 RDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCYes
Buffered/RegisteredRegistered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 ECC RDIMM Motherboard Compatible
Package Content16GB DDR5 5600MHz PC5-44800 1Rx8 1.1V 288-PIN ECC RDIMM KIT

Other versions of this model

5 more in the same range

Same family, different memory, cooler or clock — compare before you commit.

Questions about this item

What motherboard slot type is required for the 288-pin RDIMM to install?

The module needs a DDR5 288-pin RDIMM slot on a server motherboard that supports registered ECC memory and 1.1 V operation.

Will the CL46 timing work alongside existing DDR5 5600 RDIMMs in the same server?

Yes, matching the DDR5 5600 speed and CL46 latency lets the memory controller run all populated slots at the rated frequency.

How can I confirm the 1Rx8 registered ECC module is detected at full capacity after installation?

Check the BIOS memory map or the OS memory report — both should show the full 16 GB per DIMM with ECC active.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.