Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Green circuit board DDR3 DIMM with black chips no heat spreader

OWC

OWC 2GB DDR3 1600 CL11 1Rx8 240-pin 1.5V Non-ECC UDIMM for HP Elite 8300

SKU CH-CPA3-VPQ8K

Adds 2 GB of DDR3-1600 CL11 memory to HP Elite 8300 SFF or Tower desktops

  • Capacity2GB
  • Type240-Pin DDR3 Non-ECC UDIMM
  • SpeedDDR3 1600 (PC3 12800)
  • CAS LatencyCL11
  • Voltage1.5V
  • ECCNo
  • 2GB DDR3-1600 module adds responsive multitasking capacity
  • CL11 timing at 1.5V delivers stable desktop operation
  • 240-pin UDIMM fits HP Elite 8300 SFF and Tower
  • JEDEC and RoHS compliant for warranty-safe upgrades
  • Single-rank 1Rx8 design simplifies installation in compatible systems

OWC 2GB DDR3 1600 Module for HP Elite 8300

This OWC module provides a 2GB DDR3 1600 PC3-12800 CL11 upgrade. It is a 240-pin unbuffered non-ECC UDIMM rated at 1.5V. The part is validated for HP Elite 8300 SFF and Tower desktops. It uses a 1Rx8 rank configuration without a heat spreader.

Suits owners of compatible HP Elite 8300 systems

Buyers needing ECC error correction or registered modules should look elsewhere. The stick is non-ECC and unbuffered only. Systems requiring higher single-module capacities or a different DDR generation will not accept this part. It is built for the specific platforms listed.

Simple DIY installation into a free UDIMM slot

Align the notch on the 240-pin edge connector with the motherboard key and press until the retention clips lock. Common issues include mixing mismatched speeds or capacities across channels. The module follows JEDEC standards for a warranty-safe upgrade.

Helstu kostir

  • 2GB DDR3-1600 module adds responsive multitasking capacity
  • CL11 timing at 1.5V delivers stable desktop operation
  • 240-pin UDIMM fits HP Elite 8300 SFF and Tower
  • JEDEC and RoHS compliant for warranty-safe upgrades
  • Single-rank 1Rx8 design simplifies installation in compatible systems

Tæknilýsing

BrandOWC
Part Number1U6D31R802GB
Capacity2GB
Type240-Pin DDR3 Non-ECC UDIMM
SpeedDDR3 1600 (PC3 12800)
CAS LatencyCL11
Voltage1.5V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemHP Elite 8300 SFF
HP Elite 8300 Tower

Aðrar útgáfur af þessari vöru

5 í viðbót í sama vöruflokki

Sama fjölskylda, mismunandi minni, kælingu eða klukkuhraða — berðu saman áður en þú ákveður þig.

Spurningar um þessa vöru

Does the HP Elite 8300 need a free 240-pin DDR3 slot to install this 2GB module?

Yes, the module uses a standard 240-pin DDR3 UDIMM form factor and requires an available DDR3 DIMM slot on the motherboard of the HP Elite 8300 SFF or Tower.

Can this CL11 1.5V DDR3 DIMM run alongside existing CL9 memory in the HP Elite 8300?

The system will operate all installed modules at the slowest common speed and highest common latency, so CL11 1.5V memory will work with CL9 modules at CL11 timings.

How can I verify the module is running at PC3-12800 1600MHz after installation?

Check the memory speed reported in the system BIOS or use a tool such as CPU-Z to confirm the module is detected at 1600MHz with CL11 timings.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.