Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Green circuit board with black memory chips and gold edge connector

OWC

OWC 4GB DDR4 2133 CL15 1.2V 288pin UDIMM memory upgrade

SKU CH-TP9Y-48FSX

Adds 4 GB of DDR4-2133 CL15 memory to compatible HP ENVY Phoenix desktops for faster multitasking

  • Capacity4GB
  • Type288-Pin DDR4 Non-ECC UDIMM
  • SpeedDDR4 2133 (PC4 17000)
  • CAS LatencyCL15
  • Voltage1.2V
  • ECCNo
  • 4GB capacity adds multitasking headroom for everyday workloads
  • DDR4 2133 speed with CL15 latency delivers responsive system performance
  • 2V low-voltage operation reduces power draw and heat
  • 288-pin UDIMM form factor fits HP Envy Phoenix 860 series desktops
  • JEDEC and RoHS compliant for a warranty-safe upgrade

HP Envy Phoenix DDR4 upgrade

This 4GB DDR4 2133MHz UDIMM is built for HP Envy Phoenix desktops including the 860-009nf, 860-010, 860-010ng, 860-011NF and 860-011no. It adds 4GB of non-ECC memory at 1.2V with CL15 timing.

Replacing lower-capacity DDR4 modules

Swapping an existing 4GB stick for this module doubles that slot's capacity, and adding it to a free slot increases total system memory without removing anything. The jump is worth it when the current amount limits multitasking or leaves headroom below the motherboard's supported maximum.

DDR4 2133MHz platform limits

The module runs at the JEDEC-standard 2133MHz data rate; the memory controller will not push it faster without overclocking support that these OEM boards typically lack. Total capacity is capped by the number of 288-pin slots and the chipset's maximum addressable memory, which the system documentation defines.

Helstu kostir

  • 4GB capacity adds multitasking headroom for everyday workloads
  • DDR4 2133 speed with CL15 latency delivers responsive system performance
  • 2V low-voltage operation reduces power draw and heat
  • 288-pin UDIMM form factor fits HP Envy Phoenix 860 series desktops
  • JEDEC and RoHS compliant for a warranty-safe upgrade

Tæknilýsing

BrandOWC
Part Number2U1D41R804GB
Capacity4GB
Type288-Pin DDR4 Non-ECC UDIMM
SpeedDDR4 2133 (PC4 17000)
CAS LatencyCL15
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemHP ENVY Phoenix 860-009nf
HP ENVY Phoenix 860-010
HP ENVY Phoenix 860-010ng
HP ENVY Phoenix 860-011NF
HP ENVY Phoenix 860-011no

Aðrar útgáfur af þessari vöru

5 í viðbót í sama vöruflokki

Sama fjölskylda, mismunandi minni, kælingu eða klukkuhraða — berðu saman áður en þú ákveður þig.

Spurningar um þessa vöru

Does the 288-pin DDR4 UDIMM fit the HP Envy Phoenix 860-010 motherboard slots?

Yes, the module is a 288-pin DDR4 UDIMM built to JEDEC specifications for the listed HP Envy Phoenix 860 models including the 860-010.

What is the correct way to seat the module and the step often missed?

Align the notch with the slot key, press down firmly until both retention clips click shut, then verify the clips are fully engaged.

Will the 1.2 V CL15 4 GB stick need any firmware updates or replacement later?

No firmware is required; the memory is a passive component rated for lifetime use under normal operating conditions.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.