暗号資産でのお支払いに対応—お手持ちのコインで、本物のハードウェアをご購入いただけます。暗号資産で支払い、本物のハードウェアに使う。 $399以上のご注文で、世界中どこでも送料無料（保険付き）。無地・ノーブランドの外箱で、ドイツから発送いたします。$399以上で送料無料（保険付き）。 注文手続きを開始すると、レートは30分間ロックされます。レートは30分間ロック。 すべての商品は未開封で、シリアル番号を確認した上で、24か月保証が付いています。未開封、24か月保証。

ウォッチリスト ログイン
Green circuit board with black memory chips and gold edge connector

OWC

OWC 4GB DDR4 2133 CL15 1.2V 288pin UDIMM memory upgrade

SKU CH-TP9Y-48FSX

Adds 4 GB of DDR4-2133 CL15 memory to compatible HP ENVY Phoenix desktops for faster multitasking

  • Capacity4GB
  • Type288-Pin DDR4 Non-ECC UDIMM
  • SpeedDDR4 2133 (PC4 17000)
  • CAS LatencyCL15
  • Voltage1.2V
  • ECCNo
  • 4GB capacity adds multitasking headroom for everyday workloads
  • DDR4 2133 speed with CL15 latency delivers responsive system performance
  • 2V low-voltage operation reduces power draw and heat
  • 288-pin UDIMM form factor fits HP Envy Phoenix 860 series desktops
  • JEDEC and RoHS compliant for a warranty-safe upgrade

HP Envy Phoenix DDR4 upgrade

This 4GB DDR4 2133MHz UDIMM is built for HP Envy Phoenix desktops including the 860-009nf, 860-010, 860-010ng, 860-011NF and 860-011no. It adds 4GB of non-ECC memory at 1.2V with CL15 timing.

Replacing lower-capacity DDR4 modules

Swapping an existing 4GB stick for this module doubles that slot's capacity, and adding it to a free slot increases total system memory without removing anything. The jump is worth it when the current amount limits multitasking or leaves headroom below the motherboard's supported maximum.

DDR4 2133MHz platform limits

The module runs at the JEDEC-standard 2133MHz data rate; the memory controller will not push it faster without overclocking support that these OEM boards typically lack. Total capacity is capped by the number of 288-pin slots and the chipset's maximum addressable memory, which the system documentation defines.

特長

  • 4GB capacity adds multitasking headroom for everyday workloads
  • DDR4 2133 speed with CL15 latency delivers responsive system performance
  • 2V low-voltage operation reduces power draw and heat
  • 288-pin UDIMM form factor fits HP Envy Phoenix 860 series desktops
  • JEDEC and RoHS compliant for a warranty-safe upgrade

仕様

BrandOWC
Part Number2U1D41R804GB
Capacity4GB
Type288-Pin DDR4 Non-ECC UDIMM
SpeedDDR4 2133 (PC4 17000)
CAS LatencyCL15
Voltage1.2V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx8
Heat SpreaderNo
Compatible SystemHP ENVY Phoenix 860-009nf
HP ENVY Phoenix 860-010
HP ENVY Phoenix 860-010ng
HP ENVY Phoenix 860-011NF
HP ENVY Phoenix 860-011no

このモデルの他のバージョン

同シリーズにさらに 5点

同じファミリーで、メモリ・クーラー・クロックが異なります — 購入前に比較してください。

この商品に関する質問

Does the 288-pin DDR4 UDIMM fit the HP Envy Phoenix 860-010 motherboard slots?

Yes, the module is a 288-pin DDR4 UDIMM built to JEDEC specifications for the listed HP Envy Phoenix 860 models including the 860-010.

What is the correct way to seat the module and the step often missed?

Align the notch with the slot key, press down firmly until both retention clips click shut, then verify the clips are fully engaged.

Will the 1.2 V CL15 4 GB stick need any firmware updates or replacement later?

No firmware is required; the memory is a passive component rated for lifetime use under normal operating conditions.

同じ売り場の商品

よく比較されている商品

同じ売り場、同じレジ — 8種類のコインと30分間のレートロック。