Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
PrimoChill G1/4 90-degree rotary elbow fitting in Razor Red finish, 15mm extension, brass body

PrimoChill

PrimoChill G1/4 90° Rotary 15mm Extension Elbow Fitting - Razor Red

SKU CH-CB4N-1MNEF

A 15 mm G1/4 90° rotary elbow fitting with 360° adjustment and 37.7 mm total height for tight liquid-cooling routing

  • TypeFittings
  • Full 360° rotary adjusts to any angle
  • 90° elbow redirects tubing runs instantly
  • 15 mm extension clears tight component gaps
  • 7 mm total height fits low-profile builds
  • SX powder coat resists corrosion in red finish

Redirects tight tubing runs

This PrimoChill G1/4 rotary elbow fitting changes a tubing run by ninety degrees while adding fifteen millimetres of extension. The male-to-female thread lets you redirect flow away from crowded components without forcing bends. A 360-degree rotary joint allows the outlet to face any direction after installation. It suits custom loops that need a quick right-angle turn with extra clearance.

G1/4 thread limits compatibility

The fitting uses a standard G1/4 thread with five millimetres of thread depth and a thirty-seven point seven millimetre total height. Only components that share this exact thread pitch and depth will seal correctly. The installed base height of fifteen millimetres determines how far the fitting sits from the mounting surface. Builders using other thread standards cannot use this part without adapters.

Fifteen millimetre extension decides fit

The single specification that decides whether this is the right part is the fifteen millimetre installed base height. If your loop needs exactly that much standoff to clear a neighbouring block or radiator, the fitting works. If the gap is larger or smaller, the extension will not solve the clearance problem and a different length is required.

Helstu kostir

  • Full 360° rotary adjusts to any angle
  • 90° elbow redirects tubing runs instantly
  • 15 mm extension clears tight component gaps
  • 7 mm total height fits low-profile builds
  • SX powder coat resists corrosion in red finish

Tæknilýsing

TypeFittings

Spurningar um þessa vöru

Should I pick the 15 mm extension or a shorter version?

This fitting provides a 15 mm installed base height; choose it when you need that extra clearance to route tubing around nearby components.

What does the 90 degree rotary angle mean once the fitting is installed in my loop?

The elbow turns the flow 90 degrees and the 360 degree rotary base lets you aim that turn in any direction without stressing the tubing.

The G1/4 thread is standard, but what does it cap in practice?

G1/4 thread depth is 5 mm, total height is 37.7 mm, and the 15 mm extension sets the maximum offset from the mounting surface.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.