Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Gold-coloured hardened steel extruder gear with five-spoke hollow design and brass reduction gear

SeulQirw LSTJ0156 Panda Claw Gold RNC Extruder Gear 3D Printers Accessory

SKU CH-AHP1-ZKXS9

Hardened steel extruder gear with gold RNC nanocoating and self-lubricating brass reducer fits Bambu Lab X1 and P1 series printers

  • TypeLSTJ0156

A X1C/P1P/P1S 3D Printers

  • X1C/P1P/P1S 3D Printers
  • A1 Extruder Gear Assembly
  • Mounting Accessories

Yfirstrikaðar útgáfur eru til, en ekki til hér.

  • Hardened steel with Gold RNC coating lasts 50% longer than standard gears
  • Self-lubricating brass gear cuts friction for smoother filament control
  • 5-spoke hollow design lowers rotational inertia for faster response
  • Direct fit for Bambu Lab X1C, X1, P1P and P1S extruders
  • Handles abrasive and flexible filaments without slippage

Gold RNC Nanocoated Extruder Gear

The SeulQirw LSTJ0156 Panda Claw gear replaces the stock drive gear on Bambu Lab X1C, X1, P1P and P1S printers. A hardened steel core with Gold RNC nanocoating delivers a 50 percent longer lifespan than standard gears and resists corrosion from abrasive filaments such as CF-PA and GF-PETG.

Makers printing carbon-fibre

This upgrade suits owners of the listed Bambu Lab models who need reliable extrusion of filled or flexible materials. Builders using other printer brands or those who only print standard PLA and PETG without abrasion concerns will not benefit from the specialised coating.

50 percent longer gear life

The Gold RNC nanocoating on hardened steel is the single specification that determines whether this part solves your wear problems. If your current gear degrades quickly with composite filaments, the measured durability gain addresses that failure mode directly.

Helstu kostir

  • Hardened steel with Gold RNC coating lasts 50% longer than standard gears
  • Self-lubricating brass gear cuts friction for smoother filament control
  • 5-spoke hollow design lowers rotational inertia for faster response
  • Direct fit for Bambu Lab X1C, X1, P1P and P1S extruders
  • Handles abrasive and flexible filaments without slippage

Tæknilýsing

BrandSeulQirw
ModelLSTJ0156
Part NumberLSTJ0156
TypeLSTJ0156

Spurningar um þessa vöru

How often will the Gold RNC nanocoated hardened steel gear need replacement compared to a standard gear?

The Gold RNC nanocoating gives the hardened steel gear a 50% longer lifespan than standard gears, so replacement intervals are extended accordingly.

Which component reaches its wear limit first when printing abrasive filaments like CF-PA or GF-PETG all day?

The hardened steel drive gear with Gold RNC nanocoating resists abrasion far better than standard steel, so the self-lubricating brass reducing gear becomes the first wear point under sustained abrasive loads.

Does the 5-spoke hollow design change motor heat or noise during continuous high-speed printing?

The lightweight 5-spoke hollow design lowers rotational inertia, letting the extruder motor accelerate faster with less torque ripple, which reduces motor heating and acoustic noise during long high-speed runs.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.