Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Gold-coloured hardened steel extruder gear with five-spoke hollow design and brass reduction gear

SeulQirw LSTJ0156 Panda Claw Gold RNC Extruder Gear 3D Printers Accessory

SKU CH-AHP1-ZKXS9

Hardened steel extruder gear with gold RNC nanocoating and self-lubricating brass reducer fits Bambu Lab X1 and P1 series printers

  • TypeLSTJ0156

A X1C/P1P/P1S 3D Printers

  • X1C/P1P/P1S 3D Printers
  • A1 Extruder Gear Assembly
  • Mounting Accessories

Yliviivatut versiot ovat olemassa, mutta niitä ei ole varastossa täällä.

  • Hardened steel with Gold RNC coating lasts 50% longer than standard gears
  • Self-lubricating brass gear cuts friction for smoother filament control
  • 5-spoke hollow design lowers rotational inertia for faster response
  • Direct fit for Bambu Lab X1C, X1, P1P and P1S extruders
  • Handles abrasive and flexible filaments without slippage

Gold RNC Nanocoated Extruder Gear

The SeulQirw LSTJ0156 Panda Claw gear replaces the stock drive gear on Bambu Lab X1C, X1, P1P and P1S printers. A hardened steel core with Gold RNC nanocoating delivers a 50 percent longer lifespan than standard gears and resists corrosion from abrasive filaments such as CF-PA and GF-PETG.

Makers printing carbon-fibre

This upgrade suits owners of the listed Bambu Lab models who need reliable extrusion of filled or flexible materials. Builders using other printer brands or those who only print standard PLA and PETG without abrasion concerns will not benefit from the specialised coating.

50 percent longer gear life

The Gold RNC nanocoating on hardened steel is the single specification that determines whether this part solves your wear problems. If your current gear degrades quickly with composite filaments, the measured durability gain addresses that failure mode directly.

Kohokohdat

  • Hardened steel with Gold RNC coating lasts 50% longer than standard gears
  • Self-lubricating brass gear cuts friction for smoother filament control
  • 5-spoke hollow design lowers rotational inertia for faster response
  • Direct fit for Bambu Lab X1C, X1, P1P and P1S extruders
  • Handles abrasive and flexible filaments without slippage

Tekniset tiedot

BrandSeulQirw
ModelLSTJ0156
Part NumberLSTJ0156
TypeLSTJ0156

Kysymyksiä tästä tuotteesta

How often will the Gold RNC nanocoated hardened steel gear need replacement compared to a standard gear?

The Gold RNC nanocoating gives the hardened steel gear a 50% longer lifespan than standard gears, so replacement intervals are extended accordingly.

Which component reaches its wear limit first when printing abrasive filaments like CF-PA or GF-PETG all day?

The hardened steel drive gear with Gold RNC nanocoating resists abrasion far better than standard steel, so the self-lubricating brass reducing gear becomes the first wear point under sustained abrasive loads.

Does the 5-spoke hollow design change motor heat or noise during continuous high-speed printing?

The lightweight 5-spoke hollow design lowers rotational inertia, letting the extruder motor accelerate faster with less torque ripple, which reduces motor heating and acoustic noise during long high-speed runs.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.