Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Small black graphics card fan with 55mm blades and 42mm mounting holes, 3-pin connector

SXDOOL

SXDOOL MGT6012YR-O15 graphics card fan 42mm hole distance 55mm blade 0.37A 3-pin

SKU CH-A34Z-BVF3P

Replaces a graphics card cooler with a 55 mm blade, 42 mm mounting spacing and a three-pin 0.37 A connector

  • Direct replacement for compatible graphics cards with 42mm hole spacing
  • Three-wire connection enables speed monitoring through standard 3-pin header
  • 55mm blade diameter moves air across heatsink surfaces efficiently
  • Low 0.37A current draw reduces load on graphics card power circuitry
  • Compact 601 form factor fits tight spaces between expansion slots

SXDOOL MGT6012YR-O15 42 mm Fan

The SXDOOL MGT6012YR-O15 is a replacement graphics card fan with a 42 mm mounting hole spacing and a 55 mm blade diameter. It connects via a 3-pin plug and draws 0.37 A. The unit ships new in a 15 cm cube package weighing 0.5 kg.

Suits DIY GPU cooler repairs; not for case airflow

This fan is built for graphics card cooler assemblies that use the exact 42 mm hole pattern. It will not fit standard case fan mounts or coolers with different screw spacing. Buyers needing chassis intake or exhaust should look at case-specific fans instead.

55 mm blade moves air for targeted GPU cooling

The compact blade provides focused airflow directly over a graphics card heatsink. It handles the thermal load of the original cooler it replaces. It runs out of capacity when the heatsink design demands higher static pressure or a larger blade area than 55 mm can supply.

Helstu kostir

  • Direct replacement for compatible graphics cards with 42mm hole spacing
  • Three-wire connection enables speed monitoring through standard 3-pin header
  • 55mm blade diameter moves air across heatsink surfaces efficiently
  • Low 0.37A current draw reduces load on graphics card power circuitry
  • Compact 601 form factor fits tight spaces between expansion slots

Tæknilýsing

Engin birt tæknilýsing fyrir þessa vöru enn.

Spurningar um þessa vöru

Does my graphics card have a 42mm mounting pattern for this 55mm blade fan?

The fan uses a 42mm square hole spacing and a 55mm blade diameter, so it fits coolers drilled to that exact pattern.

Will the 3-pin connector work with an older 4-pin GPU fan header?

A 3-pin plug fits a 4-pin header; the fan will run at full speed unless the header supports voltage control.

How can I confirm the fan is drawing 0.37A after installation?

Check the GPU fan RPM in monitoring software and verify the current draw matches the 0.37A rating under load.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.