Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Ten green rectangular circuit boards with adjustable voltage regulators and solder points

Vszerda

Vszerda LM337 Adjustable Power Supply Module XR-103 10Pcs

SKU CH-8F8H-2WASD

Pack of ten adjustable modules delivering ±1.25 V to 30 V at 1.5 A with short-circuit and thermal protection

  • ±DC 1.25V to 30V adjustable output for flexible prototyping
  • Guaranteed 1.5A output current powers demanding circuits
  • 01% line regulation keeps voltage stable under supply changes
  • 80dB ripple rejection delivers clean power for sensitive components
  • circuit, overcurrent and overheating protection safeguards your build

LM337 Adjustable Regulator Module

The Vszerda XR-103 is a dual-polarity linear regulator board built around the LM337 and its positive counterpart. Each module accepts a centre-tapped AC input up to 28 V and delivers a continuously adjustable output from 1.25 V to 30 V at up to 1.5 A. The pack contains ten identical boards for prototyping or small-run production.

Integration Into A Prototype Build

The three-wire AC input connects directly to a suitable transformer secondary, so no separate rectifier board is required. Each module provides both positive and negative rails from a single PCB, freeing bench space and reducing wiring compared with two single-ended regulators. Designers must provide adequate heatsinking for the pass devices when operating near the 1.5 A limit.

Thermals Noise And Power Draw

Linear regulation keeps output ripple very low, with a typical rejection ratio of 80 dB. Load regulation is 0.1 % and line regulation is 0.01 %, so voltage remains stable as current demand changes. Built-in short-circuit, overcurrent and thermal-shutdown circuits protect the silicon during fault conditions, but sustained high current will raise device temperature significantly.

Helstu kostir

  • ±DC 1.25V to 30V adjustable output for flexible prototyping
  • Guaranteed 1.5A output current powers demanding circuits
  • 01% line regulation keeps voltage stable under supply changes
  • 80dB ripple rejection delivers clean power for sensitive components
  • circuit, overcurrent and overheating protection safeguards your build

Tæknilýsing

Engin birt tæknilýsing fyrir þessa vöru enn.

Spurningar um þessa vöru

What is the guaranteed output current before the protection limits activate?

The module guarantees 1.5A output current with overcurrent and overheating protection.

How much heat or noise does the board produce when running continuously?

Linear regulators dissipate heat proportional to the input-output voltage difference and load current; no fan is included.

What external AC source must I already have to power these modules?

You need a dual AC supply below 28V with three wires to feed the board.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.