Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Clear acrylic dog-bone shaped stackable case for Raspberry Pi, six transparent layers with open port access

yahboom

yahboom Raspberry Pi Cluster Case 6-Layer Acrylic Dog Bone Plate Stack Clear Case Accessories

SKU CH-KQAD-RY052

A clear six-layer acrylic stack holds up to six Raspberry Pi boards while keeping every port, GPIO header and card slot accessible

  • CPU TypeOther
  • Full port and GPIO access while the Pi is mounted
  • Crystal-clear acrylic for unobstructed visual monitoring
  • Stackable up to six layers for scalable clusters
  • Tool-free assembly for quick, hassle-free setup
  • Flat top roof supports hubs, heatsinks or switches

6-Layer Acrylic Stack for Raspberry Pi

The Yahboom cluster case is a clear acrylic enclosure designed to hold up to six Raspberry Pi boards in a vertical stack. It supports Pi 3 B+, Pi 3 B, Pi 2 B and Pi B+ models, keeping every port, GPIO header and card slot accessible. Tool-free assembly lets you build a compact cluster or a single-node setup in minutes. The transparent plates give full visibility of board status LEDs and component layout.

Cluster builders and single-board users

Makers building a multi-node Kubernetes or Docker swarm cluster will appreciate the scalable 1-to-6 layer design and open cable routing. Hobbyists wanting a single protective shell with a flat roof for a USB hub or heatsink also benefit. Users of Raspberry Pi 4, Pi 5 or Compute Module boards cannot use this case, as the cut-outs only match the older form factor. Anyone needing a fully sealed, dust-proof or ruggedised enclosure should look elsewhere.

Compatibility limited to Pi 3 B+ and earlier

The acrylic plates are cut specifically for the port arrangement and mounting holes found on Pi 3 B+, Pi 3 B, Pi 2 B and Pi B+ boards. This physical fit is the single specification that determines whether the case works for your hardware. Newer Raspberry Pi models have different port layouts and screw positions, so they will not align with the layers or allow access to connectors.

Helstu kostir

  • Full port and GPIO access while the Pi is mounted
  • Crystal-clear acrylic for unobstructed visual monitoring
  • Stackable up to six layers for scalable clusters
  • Tool-free assembly for quick, hassle-free setup
  • Flat top roof supports hubs, heatsinks or switches

Tæknilýsing

CPU TypeOther

Spurningar um þessa vöru

What spacing hardware is included to separate the six acrylic layers in the stack?

The kit uses nylon standoffs and screws that slot through the dog-bone cut-outs on each layer, letting you choose any height from one to six boards.

Which step do builders most often miss when assembling the tool-free acrylic cluster case?

Forgetting to peel the protective film from both sides of every acrylic sheet before tightening the standoffs, which traps bubbles and makes the case look cloudy.

What part of the clear acrylic enclosure is most likely to need replacement after repeated re-stacking?

The dog-bone mounting tabs can crack if the standoffs are over-tightened; keeping spare acrylic layers on hand lets you swap a damaged plate without rebuilding the whole stack.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.