Prijímame kryptomeny — takže mince, ktoré držíte, môžete zameniť za skutočný hardvér.Plaťte v krypte, miňte ho na skutočný hardvér. Poistená doprava zadarmo po celom svete nad 399 $. Neutrálne kartóny bez potlače, odosielané z Nemecka.Poistená doprava zadarmo nad 399 $. Váš kurz je zablokovaný na 30 minút hneď po otvorení pokladne.Kurz zablokovaný na 30 minút. Každý produkt je zapečatený, jeho sériové číslo je overené a vzťahuje sa naň 24-mesačná záruka.Zapečatené, 24-mesačná záruka.

Sledované položky Prihlásiť sa
Clear acrylic dog-bone shaped stackable case for Raspberry Pi, six transparent layers with open port access

yahboom

yahboom Raspberry Pi Cluster Case 6-Layer Acrylic Dog Bone Plate Stack Clear Case Accessories

SKU CH-KQAD-RY052

A clear six-layer acrylic stack holds up to six Raspberry Pi boards while keeping every port, GPIO header and card slot accessible

  • CPU TypeOther
  • Full port and GPIO access while the Pi is mounted
  • Crystal-clear acrylic for unobstructed visual monitoring
  • Stackable up to six layers for scalable clusters
  • Tool-free assembly for quick, hassle-free setup
  • Flat top roof supports hubs, heatsinks or switches

6-Layer Acrylic Stack for Raspberry Pi

The Yahboom cluster case is a clear acrylic enclosure designed to hold up to six Raspberry Pi boards in a vertical stack. It supports Pi 3 B+, Pi 3 B, Pi 2 B and Pi B+ models, keeping every port, GPIO header and card slot accessible. Tool-free assembly lets you build a compact cluster or a single-node setup in minutes. The transparent plates give full visibility of board status LEDs and component layout.

Cluster builders and single-board users

Makers building a multi-node Kubernetes or Docker swarm cluster will appreciate the scalable 1-to-6 layer design and open cable routing. Hobbyists wanting a single protective shell with a flat roof for a USB hub or heatsink also benefit. Users of Raspberry Pi 4, Pi 5 or Compute Module boards cannot use this case, as the cut-outs only match the older form factor. Anyone needing a fully sealed, dust-proof or ruggedised enclosure should look elsewhere.

Compatibility limited to Pi 3 B+ and earlier

The acrylic plates are cut specifically for the port arrangement and mounting holes found on Pi 3 B+, Pi 3 B, Pi 2 B and Pi B+ boards. This physical fit is the single specification that determines whether the case works for your hardware. Newer Raspberry Pi models have different port layouts and screw positions, so they will not align with the layers or allow access to connectors.

Prednosti

  • Full port and GPIO access while the Pi is mounted
  • Crystal-clear acrylic for unobstructed visual monitoring
  • Stackable up to six layers for scalable clusters
  • Tool-free assembly for quick, hassle-free setup
  • Flat top roof supports hubs, heatsinks or switches

Špecifikácie

CPU TypeOther

Otázky k tomuto produktu

What spacing hardware is included to separate the six acrylic layers in the stack?

The kit uses nylon standoffs and screws that slot through the dog-bone cut-outs on each layer, letting you choose any height from one to six boards.

Which step do builders most often miss when assembling the tool-free acrylic cluster case?

Forgetting to peel the protective film from both sides of every acrylic sheet before tightening the standoffs, which traps bubbles and makes the case look cloudy.

What part of the clear acrylic enclosure is most likely to need replacement after repeated re-stacking?

The dog-bone mounting tabs can crack if the standoffs are over-tightened; keeping spare acrylic layers on hand lets you swap a damaged plate without rebuilding the whole stack.

Aj v tomto oddelení

Zákazníci tiež porovnávali

Rovnaké oddelenie, rovnaká pokladňa — osem mien a kurz zablokovaný na 30 minút.