OWC 8GB DDR5 4800 CL40 262-pin 1.1V SODIMM memory upgrade
- 8GB
- 262-Pin DDR5 Non-EC…
Priimame kriptovaliutą — taip monetos, kurias turite, gali nupirkti tikrą techniką.Mokėkite kriptovaliuta, išleiskite ją tikrai technikai. Nemokamas apdraustas pristatymas visame pasaulyje virš 399 $. Paprastos, be žymų siuntos dėžės, siunčiamos iš Vokietijos.Nemokamas apdraustas pristatymas virš 399 $. Jūsų kursas fiksuojamas 30 minučių, kai tik prasideda atsiskaitymas.Kursas fiksuojamas 30 minučių. Kiekvienas gaminys užplombuotas, jo serijos numeris patikrintas, ir jam taikoma 24 mėnesių garantija.Užplombuota, 24 mėnesių garantija.
OWC
8GB DDR5 4800 CL40 UDIMM upgrade for Dell OptiPlex 7000 Tower, 7010 SFF Plus, 7010 Tower Plus and XE4 Tower
This OWC module adds 8GB of DDR5 4800 memory to Dell OptiPlex 7000 Tower, 7010 SFF Plus, 7010 Tower Plus and XE4 Tower systems. It uses a 288-pin UDIMM form factor with CL40 latency and 1.1V operation. The single-rank 1Rx16 design meets JEDEC standards for a warranty-safe installation. No heat spreader is fitted.
Buyers with other desktops, laptops or workstations should verify their platform accepts DDR5 4800 UDIMMs before purchasing. Systems requiring ECC or registered memory cannot use this non-ECC unbuffered module. The 8GB capacity may limit users running heavy virtualisation or large creative workloads.
Installation frees no additional slots beyond the one occupied. The module draws power directly from the slot at 1.1V with no extra cabling needed. It replaces Dell part numbers AB883073 and SNP29NJ4C/8G for direct compatibility. Ensure the system BIOS recognises the new capacity after fitting.
| Brand | OWC |
|---|---|
| Part Number | 4U8D51R608GB |
| Capacity | 8GB |
| Type | 288-Pin DDR5 Non-ECC UDIMM |
| Speed | DDR5 4800 (PC5 38400) |
| CAS Latency | CL40 |
| Voltage | 1.1V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Rank | 1Rx16 |
| Heat Spreader | No |
| Compatible System | Dell OptiPlex 7000 Tower Dell OptiPlex 7010 SFF Plus Dell OptiPlex 7010 Tower Plus Dell OptiPlex XE4 Tower |
Kiti šio modelio variantai
Ta pati šeima, bet skiriasi atmintis, aušintuvas ar dažnis — palyginkite prieš apsispręsdami.
No extra parts are required; the module fits the standard DDR5 UDIMM slot and runs at the JEDEC 1.1V level used by the OptiPlex 7000 Tower, 7010 SFF Plus, 7010 Tower Plus and XE4 Tower.
The system will run all installed DDR5 modules at the lowest common speed and latency; this stick is rated CL40 at 4800 MHz, so faster modules will down-clock to match.
Check the BIOS memory information or a tool such as CPU-Z; it should report 4800 MHz, CL40 timing and 8 GB capacity for the new DIMM.
Taip pat šiame skyriuje
Ta pati lentyna, tas pats atsiskaitymas — aštuonios monetos ir 30 minučių fiksuotas kursas.
Tai, kuo mokate, ir valiuta, kuria matote kainas.
Išsiunčiama iš Jūsų piniginės atsiskaitant
Tik rodoma — katalogo kainos nurodytos doleriais
Tokios valiutos nerasta.
Pasirinkite kalbą, kuria Jums kalbės svetainė.
Pirmą kartą čia?
Jau turite paskyrą?
Automatinio atstatymo nėra: ši parduotuvė nesiunčia jokių el. laiškų, todėl nėra jokios vienkartinės nuorodos, kurios būtų galima paprašyti. Palikite adresą paskyroje, ir juo bus pasirūpinta rankiniu būdu.
Prašymas užfiksuotas
Į Jūsų pašto dėžutę niekas nekeliauja — ši parduotuvė apskritai nesiunčia jokių el. laiškų. Šiuos prašymus kažkas peržiūri rankiniu būdu.
Prisiminėte?