Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Green rectangular circuit board with gold edge connectors and black memory chips

OWC

OWC 8GB DDR5 4800 CL40 1Rx16 1.1V UDIMM memory upgrade

SKU CH-KH5Z-MEBN8

8GB DDR5 4800 CL40 UDIMM upgrade for Dell OptiPlex 7000 Tower, 7010 SFF Plus, 7010 Tower Plus and XE4 Tower

  • Capacity8GB
  • Type288-Pin DDR5 Non-ECC UDIMM
  • SpeedDDR5 4800 (PC5 38400)
  • CAS LatencyCL40
  • Voltage1.1V
  • ECCNo
  • 8GB capacity expands multitasking headroom for demanding workloads
  • DDR5 4800 speed delivers high bandwidth for responsive performance
  • CL40 latency at 1.1V balances timing with efficient power use
  • JEDEC-standard design ensures warranty-safe compatibility with listed OptiPlex systems
  • Single 1Rx16 unbuffered module simplifies DIY installation in 288-pin slots

Compatible Dell OptiPlex DDR5 upgrade

This OWC module adds 8GB of DDR5 4800 memory to Dell OptiPlex 7000 Tower, 7010 SFF Plus, 7010 Tower Plus and XE4 Tower systems. It uses a 288-pin UDIMM form factor with CL40 latency and 1.1V operation. The single-rank 1Rx16 design meets JEDEC standards for a warranty-safe installation. No heat spreader is fitted.

Suits owners of listed OptiPlex models wanting

Buyers with other desktops, laptops or workstations should verify their platform accepts DDR5 4800 UDIMMs before purchasing. Systems requiring ECC or registered memory cannot use this non-ECC unbuffered module. The 8GB capacity may limit users running heavy virtualisation or large creative workloads.

Fits a standard DDR5 DIMM slot on supported

Installation frees no additional slots beyond the one occupied. The module draws power directly from the slot at 1.1V with no extra cabling needed. It replaces Dell part numbers AB883073 and SNP29NJ4C/8G for direct compatibility. Ensure the system BIOS recognises the new capacity after fitting.

Přednosti

  • 8GB capacity expands multitasking headroom for demanding workloads
  • DDR5 4800 speed delivers high bandwidth for responsive performance
  • CL40 latency at 1.1V balances timing with efficient power use
  • JEDEC-standard design ensures warranty-safe compatibility with listed OptiPlex systems
  • Single 1Rx16 unbuffered module simplifies DIY installation in 288-pin slots

Specifikace

BrandOWC
Part Number4U8D51R608GB
Capacity8GB
Type288-Pin DDR5 Non-ECC UDIMM
SpeedDDR5 4800 (PC5 38400)
CAS LatencyCL40
Voltage1.1V
ECCNo
Buffered/RegisteredUnbuffered
Rank1Rx16
Heat SpreaderNo
Compatible SystemDell OptiPlex 7000 Tower
Dell OptiPlex 7010 SFF Plus
Dell OptiPlex 7010 Tower Plus
Dell OptiPlex XE4 Tower

Další verze tohoto modelu

Dalších 5 v této řadě

Stejná řada, jiná paměť, chladič nebo takt — porovnejte, než se rozhodnete.

Otázky k tomuto produktu

Will my OptiPlex 7000 Tower need any other parts before I install this 288-pin 1.1V DDR5 UDIMM?

No extra parts are required; the module fits the standard DDR5 UDIMM slot and runs at the JEDEC 1.1V level used by the OptiPlex 7000 Tower, 7010 SFF Plus, 7010 Tower Plus and XE4 Tower.

How will this CL40 4800 MHz DDR5 module behave alongside any existing DDR5 memory I keep in the same OptiPlex?

The system will run all installed DDR5 modules at the lowest common speed and latency; this stick is rated CL40 at 4800 MHz, so faster modules will down-clock to match.

How can I confirm the module is recognised at 4800 MHz CL40 after installation?

Check the BIOS memory information or a tool such as CPU-Z; it should report 4800 MHz, CL40 timing and 8 GB capacity for the new DIMM.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.