OWC 8GB DDR5 4800 CL40 262-pin 1.1V SODIMM memory upgrade
- 8GB
- 262-Pin DDR5 Non-EC…
Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.
OWC
8GB DDR5 4800 CL40 UDIMM upgrade for Dell OptiPlex 7000 Tower, 7010 SFF Plus, 7010 Tower Plus and XE4 Tower
This OWC module adds 8GB of DDR5 4800 memory to Dell OptiPlex 7000 Tower, 7010 SFF Plus, 7010 Tower Plus and XE4 Tower systems. It uses a 288-pin UDIMM form factor with CL40 latency and 1.1V operation. The single-rank 1Rx16 design meets JEDEC standards for a warranty-safe installation. No heat spreader is fitted.
Buyers with other desktops, laptops or workstations should verify their platform accepts DDR5 4800 UDIMMs before purchasing. Systems requiring ECC or registered memory cannot use this non-ECC unbuffered module. The 8GB capacity may limit users running heavy virtualisation or large creative workloads.
Installation frees no additional slots beyond the one occupied. The module draws power directly from the slot at 1.1V with no extra cabling needed. It replaces Dell part numbers AB883073 and SNP29NJ4C/8G for direct compatibility. Ensure the system BIOS recognises the new capacity after fitting.
| Brand | OWC |
|---|---|
| Part Number | 4U8D51R608GB |
| Capacity | 8GB |
| Type | 288-Pin DDR5 Non-ECC UDIMM |
| Speed | DDR5 4800 (PC5 38400) |
| CAS Latency | CL40 |
| Voltage | 1.1V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Rank | 1Rx16 |
| Heat Spreader | No |
| Compatible System | Dell OptiPlex 7000 Tower Dell OptiPlex 7010 SFF Plus Dell OptiPlex 7010 Tower Plus Dell OptiPlex XE4 Tower |
Tämän mallin muut versiot
Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.
No extra parts are required; the module fits the standard DDR5 UDIMM slot and runs at the JEDEC 1.1V level used by the OptiPlex 7000 Tower, 7010 SFF Plus, 7010 Tower Plus and XE4 Tower.
The system will run all installed DDR5 modules at the lowest common speed and latency; this stick is rated CL40 at 4800 MHz, so faster modules will down-clock to match.
Check the BIOS memory information or a tool such as CPU-Z; it should report 4800 MHz, CL40 timing and 8 GB capacity for the new DIMM.
Myös tällä osastolla
Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.
Valuutta, jolla maksetaan, sekä valuutta, jossa hinnat näytetään.
Lähetetään lompakostasi kassalla
Vain näyttöä varten — hinnat ovat Yhdysvaltain dollareissa
Valuuttaa ei löytynyt.
Valitse kieli, jolla sivusto puhuu sinulle.
Ei vastaavaa kieltä.
Uusi täällä?
Onko sinulla jo tili?
Automaattista palautusta ei ole: kauppa ei lähetä sähköpostia lainkaan, joten kertakäyttöistä linkkiä ei ole mistä pyytää. Jätä osoite tilille, niin se käsitellään käsin.
Pyyntö kirjattu
Mikään ei ole tulossa sähköpostiisi — tämä kauppa ei lähetä sähköpostia lainkaan. Joku käsittelee nämä pyynnöt käsin.
Muistitko sen?