Priimame kriptovaliutą — taip monetos, kurias turite, gali nupirkti tikrą techniką.Mokėkite kriptovaliuta, išleiskite ją tikrai technikai. Nemokamas apdraustas pristatymas visame pasaulyje virš 399 $. Paprastos, be žymų siuntos dėžės, siunčiamos iš Vokietijos.Nemokamas apdraustas pristatymas virš 399 $. Jūsų kursas fiksuojamas 30 minučių, kai tik prasideda atsiskaitymas.Kursas fiksuojamas 30 minučių. Kiekvienas gaminys užplombuotas, jo serijos numeris patikrintas, ir jam taikoma 24 mėnesių garantija.Užplombuota, 24 mėnesių garantija.

Stebimos prekės Prisijungti
White 2.85 mm nylon filament on a 5 inch spool

Taulman 3D

Taulman 3D Nylon 230 Filament 2.85mm 1lb Natural

SKU CH-B737-MH84T

Nylon 6 filament printing at 228-235 °C on unheated beds, 4980 PSI tensile with 417 % elongation, 2.85 mm diameter on a 5-inch spool

  • ColorNatural
  • TypeFilament
  • Prints on cold beds without heated enclosure
  • Low 228–235 °C printing range eases extrusion
  • Standard Nylon 6 with no chemical additives
  • High 417 % elongation absorbs impact loads
  • 4 980 PSI tensile strength for functional parts

Taulman Nylon 230 Filament 2.85mm 1lb

Taulman Nylon 230 is a standard Nylon 6 filament developed for 3D printers with cold print beds and lower temperature capabilities. It prints between 228C and 235C without requiring a heated bed. The 1lb spool suits makers producing light-load gears, fan blades, housings, phone covers, protective enclosures and cosmetics containers.

Low-temperature printing on ambient beds

The material extrudes at 230C to 238C while the print bed stays at ambient temperature, reducing power draw and warm-up time. Standard Nylon 6 composition contains no chemical additives, limiting odour and fumes during normal use. Tensile strength reaches 4980 PSI with 417% elongation, indicating tough, flexible parts straight from the printer.

Upgrade from higher-temp nylons for cold-bed systems

This filament replaces standard nylons that demand heated chambers or beds above ambient, letting older or entry-level printers produce durable nylon parts. The jump is worth it when you need Nylon 6 toughness but your hardware caps nozzle temperature near 235C and lacks bed heating. Buyers needing larger spool sizes or higher temperature resistance should look elsewhere.

Privalumai

  • Prints on cold beds without heated enclosure
  • Low 228–235 °C printing range eases extrusion
  • Standard Nylon 6 with no chemical additives
  • High 417 % elongation absorbs impact loads
  • 4 980 PSI tensile strength for functional parts

Specifikacijos

Brandtaulman3d
ColorNatural
TypeFilament

Klausimai apie šią prekę

How do I install Taulman Nylon 230 on a printer with a cold bed and what step is often missed?

Set the hot-end between 228C and 235C, leave the bed at ambient temperature, and dry the filament before printing because Nylon 6 absorbs moisture quickly.

What maintenance or replacement will this 1 lb spool of 2.85 mm Nylon 230 need later?

The spool will be consumed and must be replaced; store any unused portion in a sealed bag with desiccant to prevent moisture uptake.

What limit appears first during a long print with this filament?

Moisture absorption during extended printing can cause bubbles and layer adhesion loss, so keep the material dry throughout the job.

Taip pat šiame skyriuje

Kiti pirkėjai taip pat lygino

Ta pati lentyna, tas pats atsiskaitymas — aštuonios monetos ir 30 minučių fiksuotas kursas.