Prijímame kryptomeny — takže mince, ktoré držíte, môžete zameniť za skutočný hardvér.Plaťte v krypte, miňte ho na skutočný hardvér. Poistená doprava zadarmo po celom svete nad 399 $. Neutrálne kartóny bez potlače, odosielané z Nemecka.Poistená doprava zadarmo nad 399 $. Váš kurz je zablokovaný na 30 minút hneď po otvorení pokladne.Kurz zablokovaný na 30 minút. Každý produkt je zapečatený, jeho sériové číslo je overené a vzťahuje sa naň 24-mesačná záruka.Zapečatené, 24-mesačná záruka.

Sledované položky Prihlásiť sa
White 2.85 mm nylon filament on a 5 inch spool

Taulman 3D

Taulman 3D Nylon 230 Filament 2.85mm 1lb Natural

SKU CH-B737-MH84T

Nylon 6 filament printing at 228-235 °C on unheated beds, 4980 PSI tensile with 417 % elongation, 2.85 mm diameter on a 5-inch spool

  • ColorNatural
  • TypeFilament
  • Prints on cold beds without heated enclosure
  • Low 228–235 °C printing range eases extrusion
  • Standard Nylon 6 with no chemical additives
  • High 417 % elongation absorbs impact loads
  • 4 980 PSI tensile strength for functional parts

Taulman Nylon 230 Filament 2.85mm 1lb

Taulman Nylon 230 is a standard Nylon 6 filament developed for 3D printers with cold print beds and lower temperature capabilities. It prints between 228C and 235C without requiring a heated bed. The 1lb spool suits makers producing light-load gears, fan blades, housings, phone covers, protective enclosures and cosmetics containers.

Low-temperature printing on ambient beds

The material extrudes at 230C to 238C while the print bed stays at ambient temperature, reducing power draw and warm-up time. Standard Nylon 6 composition contains no chemical additives, limiting odour and fumes during normal use. Tensile strength reaches 4980 PSI with 417% elongation, indicating tough, flexible parts straight from the printer.

Upgrade from higher-temp nylons for cold-bed systems

This filament replaces standard nylons that demand heated chambers or beds above ambient, letting older or entry-level printers produce durable nylon parts. The jump is worth it when you need Nylon 6 toughness but your hardware caps nozzle temperature near 235C and lacks bed heating. Buyers needing larger spool sizes or higher temperature resistance should look elsewhere.

Prednosti

  • Prints on cold beds without heated enclosure
  • Low 228–235 °C printing range eases extrusion
  • Standard Nylon 6 with no chemical additives
  • High 417 % elongation absorbs impact loads
  • 4 980 PSI tensile strength for functional parts

Špecifikácie

Brandtaulman3d
ColorNatural
TypeFilament

Otázky k tomuto produktu

How do I install Taulman Nylon 230 on a printer with a cold bed and what step is often missed?

Set the hot-end between 228C and 235C, leave the bed at ambient temperature, and dry the filament before printing because Nylon 6 absorbs moisture quickly.

What maintenance or replacement will this 1 lb spool of 2.85 mm Nylon 230 need later?

The spool will be consumed and must be replaced; store any unused portion in a sealed bag with desiccant to prevent moisture uptake.

What limit appears first during a long print with this filament?

Moisture absorption during extended printing can cause bubbles and layer adhesion loss, so keep the material dry throughout the job.

Aj v tomto oddelení

Zákazníci tiež porovnávali

Rovnaké oddelenie, rovnaká pokladňa — osem mien a kurz zablokovaný na 30 minút.