Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Silver compression fitting for 16mm rigid tubing

Bitspower

Bitspower BP-EMLA16 G1/4" Multi-Link Fitting 16mm OD Silver

SKU CH-DD8E-TFCD5 MPN BP-EMLA16

Connects 16mm rigid tubing with a G1/4" multi-link brass fitting in silver

  • TypeFittings
  • Multi-link design enables extended rigid-tube runs
  • G1/4" thread fits standard water-cooling components
  • Brass construction resists corrosion in liquid loops
  • Silver Shining finish matches metallic build themes
  • Compression seal secures 16mm OD hard tubing

G1/4" Multi-Link Fitting for 16mm OD Tubing

This compression fitting connects 16mm OD rigid tubing in custom liquid-cooling loops. It is intended for builders assembling hard-tube systems who need secure, leak-free joints with a clean silver finish.

Brass construction and compression seal

The fitting is machined from high-quality brass and uses a compression design that grips rigid tubing tightly when assembled correctly. RoHS-compliant materials meet environmental standards without affecting thermal performance or acoustic profile of the loop.

Extends existing hard-tube runs

The multi-link design allows straight extensions or angled connections between 16mm OD tubes without adding extra components. Builders replacing push-fit couplers or upgrading from soft tubing gain a more rigid, maintenance-friendly joint; those needing quick-disconnect or smaller-diameter connections should look elsewhere.

Priekšrocības

  • Multi-link design enables extended rigid-tube runs
  • G1/4" thread fits standard water-cooling components
  • Brass construction resists corrosion in liquid loops
  • Silver Shining finish matches metallic build themes
  • Compression seal secures 16mm OD hard tubing

Specifikācijas

TypeFittings

Jautājumi par šo preci

How do I install the Bitspower BP-EMLA16 multi-link fitting onto 16mm OD hard tubing without leaks?

Cut the tubing square, deburr the edge, slide the compression nut and ring onto the tube, push the tube fully into the fitting body until it seats, then hand-tighten the nut firmly — the step most people skip is verifying the tube bottoms out before tightening.

What maintenance will the BP-EMLA16 fitting need over time?

Check the compression seal and O-ring whenever you drain the loop; if the O-ring shows flattening or the nut has backed off, replace the O-ring and re-torque the nut to keep the joint secure.

What is the first limitation I will hit when running the BP-EMLA16 under sustained load?

The G1/4" thread depth and brass construction set the mechanical and thermal limit — ensure the mating port provides full thread engagement so the joint stays sealed at operating temperature.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.