Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Green 100-pin SODIMM memory module with black chips

Computer Memory Solutions

Computer Memory Solutions 512MB DDR 333 SODIMM 100-Pin memory upgrade

SKU CH-Y1ZW-TZHP6

512MB DDR 333 SODIMM 100-pin memory upgrade for Kyocera FS-1100, FS-1300D, FS-C5015N, FS-C5020N, FS-C5025N and FS-C5030N printers

  • Capacity512MB
  • SpeedDDR 333 (PC 2700)
  • CAS LatencyCL2.5
  • Timing3-3-3
  • Voltage2.5V
  • ECCNo
  • 512 MB DDR 333 memory adds capacity to supported Kyocera printers
  • DDR 333 (PC 2700) speed matches original system timing for stable operation
  • CL2.5 CAS latency with 3-3-3 timing delivers responsive data access
  • 100-pin SODIMM form factor fits the designated Kyocera FS and FS-C models
  • Unbuffered 2.5 V design installs directly without extra configuration

Compatible Kyocera Printer Upgrade

This 512MB SODIMM module is built for Kyocera FS-C5015N, FS-C5020N, FS-C5025N and FS-C5030N printers. It also supports FS-1100 and FS-1300D models. The stick adds memory to the listed devices for print-job buffering and font storage. It is not for desktop or laptop motherboards.

Simple SODIMM Installation

The 100-pin SODIMM slots into the printer's memory socket without tools. Align the notch, insert at an angle, then press down until the clips latch. A common issue is seating the module fully; if the printer does not recognise the new capacity, remove and reseat the stick. No BIOS or driver updates are required.

512MB Capacity Limit

Each socket accepts a maximum of 512MB, and the system supports two sockets for a total of 1GB. This single module fills one slot completely. Installing a larger stick will not work because the controller cannot address more memory per socket. The 333MHz DDR speed matches the printer's bus.

Priekšrocības

  • 512 MB DDR 333 memory adds capacity to supported Kyocera printers
  • DDR 333 (PC 2700) speed matches original system timing for stable operation
  • CL2.5 CAS latency with 3-3-3 timing delivers responsive data access
  • 100-pin SODIMM form factor fits the designated Kyocera FS and FS-C models
  • Unbuffered 2.5 V design installs directly without extra configuration

Specifikācijas

BrandComputer Memory Solutions
ModelCM512MBPC2700100PIN
Capacity512MB
SpeedDDR 333 (PC 2700)
CAS LatencyCL2.5
Timing3-3-3
Voltage2.5V
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor Brand Chipset
Heat SpreaderNo
Compatible SystemKyocera Fs-C5015N, Fs-C5020N, Fs-C5025N, Fs-C5030N
Package Content1 Memory RAM Stick

Jautājumi par šo preci

How can I confirm the 512MB DDR 333 SODIMM is recognised by my Kyocera FS-C5025N after installation?

Power on the printer and check the system information menu; it should report the total memory as 1GB when both sockets are filled with 512MB modules.

What comes in the package and do I need any extra parts to install the 100-pin SODIMM?

The box contains one 512MB DDR 333 SODIMM stick; no additional components are required for installation.

Which capacity should I choose if my Kyocera FS-1300D has two sockets and a 1GB maximum?

Select the 512MB module; two of them will reach the 1GB limit supported by the printer.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.